fknbrkn
Hero Member
Karma: +185/-23
 Online
Posts: 1454
mk4 1.8T AUM
|
 |
« Reply #60 on: February 22, 2015, 12:10:44 PM »
|
|
|
i wrote partnumber of vag original adapters, its very cheap and its what you need
|
|
|
|
|
Logged
|
|
|
|
TijnCU
Hero Member
Karma: +60/-4
 Offline
Posts: 690
flying brick
|
|
« Reply #61 on: February 22, 2015, 12:12:35 PM »
|
|
|
Ok thanks I'll take a look  need to pass by the dealer next week anyway. ** just came from the dealer, shit those adapters are 2,20€ ex vat a piece  thanks for saving me the trouble fukenbroken! Hehe |
|
|
|
« Last Edit: February 24, 2015, 07:31:50 AM by TijnCU »
|
Logged
|
|
|
|
MadCow
Full Member
Karma: +3/-1
Offline
Posts: 108
|
|
« Reply #62 on: February 24, 2015, 08:26:45 PM »
|
|
|
Ok thanks I'll take a look need to pass by the dealer next week anyway. ** just came from the dealer, shit those adapters are 2,20€ ex vat a piece thanks for saving me the trouble fukenbroken! Hehe Yep they're great. For extra sealing you can put a small bead of RTV along the bottom edge, they're supposed to be paired with a gasket but it won't seal fully with those valve covers, and they cost more than the adaptor itself oddly enough. |
|
|
|
|
Logged
|
|
|
|
|
thelastleroy
|
|
« Reply #63 on: March 01, 2015, 09:56:50 AM »
|
|
|
Finally got the valve in the mail (authentic, undamaged) and got it installed today. Very slick operation. Going to check if the boost spike I was seeing on logs Is gone, when it's warmer outside.
|
|
|
|
|
Logged
|
|
|
|
|
|
diagnosticator
Jr. Member
Karma: +2/-0
Offline
Posts: 42
|
|
« Reply #65 on: April 20, 2015, 05:04:30 AM »
|
|
|
I'm probably going to cut the connector and wires to make a pigtail and solder up an extension wire directly. My car will never be stock again, so I don't mind hacking up the harness a bit. I wonder if dealerships sell "repair pigtails" for damaged connectors?
The dealer has repair wires, with a terminal crimped on each end. You can get only one repair wire and cut in half, for two wires with terminals. You need to match the terminals at the dealer, needed to fit the connector housings you are using. |
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #66 on: September 04, 2015, 04:49:03 AM »
|
|
|
tinju yours is mounted the opposit side. The "long" side is for pressure. Theses things getting popular in germany more and more. I just ordered the parts to save my now chra from dying again  |
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #67 on: September 04, 2015, 04:57:12 AM »
|
|
|
Your chra died?
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #68 on: September 04, 2015, 05:30:23 AM »
|
|
|
was a used turbo and started to make noise a little.
there is oil on the outside too
all of my wot logs have boost spike on the right side^^
which kills your axial bearing
leave your n249 in place kids. dont trust the internet 1337 tuners
|
|
|
|
|
Logged
|
|
|
|
A4Rich
Full Member
Karma: +10/-0
Offline
Posts: 116
|
|
« Reply #69 on: September 04, 2015, 05:47:03 AM »
|
|
|
Theses things getting popular in germany more and more. I just ordered the parts to save my now chra from dying again Have you consider what your going to use for SVDLDUVS? 225 APX values? |
|
|
|
|
Logged
|
|
|
|
TijnCU
Hero Member
Karma: +60/-4
Offline
Posts: 690
flying brick
|
|
« Reply #70 on: September 06, 2015, 05:16:05 AM »
|
|
|
I am still running this setup, on standard APX values. Works great, valve is open on cruise unless requested goes above 1300mB.
Havent looked at it anymore, because it is just like stock and works excellent. No boostleaks yet, done about 10.000km on this valve now.
Its not backwards, pressure side is on the side and turbo inlet pipe is opposite to the coil. I dont think it would hold boost when you switch them around, there is no pressurized diaphragm in this system, just a spring.
|
|
|
|
« Last Edit: September 06, 2015, 05:55:27 AM by TijnCU »
|
Logged
|
|
|
|
|
aef
|
|
« Reply #71 on: September 07, 2015, 03:48:20 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
|
|
|
aef
|
|
« Reply #73 on: October 05, 2015, 10:22:31 AM »
|
|
|
Hi, I reinstalled my N249 wiring today and did some tests. I have a small size turbo (K04-064) from the newer TFSI Mk6R or S3 8P on my 1.8t engine. My SUV is a GFB T9301 and its mounted on the cold side infront of the throttle I was under the impression that a eSUV would be much faster and my boost peaks at redline could be solved. It is faster during gearchange. There is a noticeable better boost build up. (no logs so far) It is NOT faster at redline when the throttle closes. Maybe it is just too small for my airmass. The boost spike is bigger and longer with the eSUV.  |
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #74 on: November 04, 2015, 11:05:16 PM »
|
|
|
No updates from other users?
This is a Polo WRC with same Turbo and eSUV on the Cold Side like i build it in my car.
They have all to deal with the high peak boost at redline?
|
|
|
|
|
Logged
|
|
|
|
|
