Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« on: September 17, 2014, 10:47:06 AM »
|
|
|
551D
Done immo off with 95040 tool
.bin file off old ecu still 1024kb ecu can't post as it's commercial tune
Writes fine with galletto
Car fires up for 1 or 2 secs then conks out
Any ideas?
|
|
|
Logged
|
|
|
|
armageddon
|
|
« Reply #1 on: September 17, 2014, 01:09:50 PM »
|
|
|
try to flash other 95040.bin with immo off and see if it work.
friend of mine had is ECU "blocked" by an audi dealer, I simple put another 95040.bin on it and it worked
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #2 on: September 17, 2014, 01:31:09 PM »
|
|
|
It already had the immo off but I wrote another to it to be sure.
I did think about weather it needed the throttle body alignment or idle adjustment done with vcds
|
|
|
Logged
|
|
|
|
turboat
|
|
« Reply #3 on: September 17, 2014, 03:29:12 PM »
|
|
|
Odd, sounds a lot like immo stopping the engine. Are there any fault codes?
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #4 on: September 18, 2014, 12:08:29 AM »
|
|
|
Didnt scan it as i was getting frustrated as i had to walk back and forth from my house to garage to check it on the car 4 times after re-flashing.
I had another issue were on VCDS in engine it wouldnt bring up the ecu number it was just saying THIS-IS which i belive would be THIS-IS-THE-RAM-MEMORY whihc made me think somthing was scrambled?
Its a standard chip on the bored so not sure hwo it would scramble anything.
Its now not doing that after a reflash but still the start issue
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #5 on: September 18, 2014, 01:13:06 AM »
|
|
|
Just sprung to mind, is 551D ME7.1.1??
I think i has put the immo off bin for 7.5/7.1 on there
|
|
|
Logged
|
|
|
|
turboat
|
|
« Reply #6 on: September 18, 2014, 03:12:57 AM »
|
|
|
That may well be the problem! I always immo off the file I read from the ecu, rather than using a generic one. Post up the ori EEPROM and the immo off one
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #7 on: September 18, 2014, 03:39:50 AM »
|
|
|
I was goin to but i couldnt get your tool working
Ill try post them up later when im home
|
|
|
Logged
|
|
|
|
turboat
|
|
« Reply #8 on: September 18, 2014, 04:08:27 AM »
|
|
|
What was the issue you had?
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #9 on: September 18, 2014, 05:07:14 AM »
|
|
|
it wouldnt run, somthing about python?
|
|
|
Logged
|
|
|
|
turboat
|
|
« Reply #10 on: September 18, 2014, 05:08:30 AM »
|
|
|
Use the version in the .zip, you need all the files in that zip in the same directory as the tool.
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #11 on: September 18, 2014, 09:43:28 AM »
|
|
|
|
|
|
Logged
|
|
|
|
|