Mike Tries
Newbie
Karma: +0/-0
Offline
Posts: 6
|
 |
« Reply #765 on: November 29, 2022, 06:17:14 AM »
|
|
|
Oh that fixed her right up! Tune works on a 2003 Audi A4 Quattro Avant. Thank you for your help!
|
|
|
Logged
|
|
|
|
raresz
Newbie
Karma: +0/-1
Offline
Posts: 14
|
 |
« Reply #766 on: May 21, 2023, 04:41:28 AM »
|
|
|
Hi guys,
I'm learning ME7.5 and always when i ask somebody about something they always say: "check the nefmoto community stage1 project". So i did.
I'm bit confused of this what happens in that files as they look like this.
Maybe LAMFA looks ok, but this what i found in KFMIRL looks like some random values. Same with KFMIOP. I have downloaded all 3 files(stock, mod, and xdf) from first post.
What is wrong with those files/my tunerpro?
|
|
|
Logged
|
|
|
|
kubawd
Jr. Member

Karma: +5/-1
Online
Posts: 37
|
 |
« Reply #767 on: May 21, 2023, 03:33:12 PM »
|
|
|
It's showing percentage difference between compared bins. Change your compare mode setting from percentage to absolute.
|
|
|
Logged
|
|
|
|
Chunky711
Newbie
Karma: +0/-0
Offline
Posts: 1
|
 |
« Reply #768 on: December 24, 2023, 12:54:04 PM »
|
|
|
Saying thanks! Picked up 2003 A4 Avant in good working condition. Was thinking of spending approx $500 CAD on a stage 1 tune... Eventually found this forum, joined, learned. Had 'blue cable' already. Took the advice of using a car charger to keep the voltage up. Backed up my BIN. Flashed stock bin. Would not start - flash back to my BIN. Car OK again. Learned to edit that single HEX value in stock file and then re-checksum it. Flashed stock BIN again, car works fine. Stage 1 V7 BIN did not have that HEX value, so flashed it. Car works fine. Pulls noticeably harder and runs just like stock. Awesome! BIG THANKS It's like a Christmas present to myself! 
|
|
|
Logged
|
|
|
|
_nameless
|
 |
« Reply #769 on: December 24, 2023, 06:35:28 PM »
|
|
|
Saying thanks! Picked up 2003 A4 Avant in good working condition. Was thinking of spending approx $500 CAD on a stage 1 tune... Eventually found this forum, joined, learned. Had 'blue cable' already. Took the advice of using a car charger to keep the voltage up. Backed up my BIN. Flashed stock bin. Would not start - flash back to my BIN. Car OK again. Learned to edit that single HEX value in stock file and then re-checksum it. Flashed stock BIN again, car works fine. Stage 1 V7 BIN did not have that HEX value, so flashed it. Car works fine. Pulls noticeably harder and runs just like stock. Awesome! BIG THANKS It's like a Christmas present to myself!  This is a prime example why I think these community tune threads are stupid. Literally someone who is just looking for a free file and not interested in actually learning how to tune their car. I mean correct me if I'm wrong but doesn't that circumvent the entire point of this this forum??
|
|
|
Logged
|
Giving your mom a tuneup
|
|
|
nathanaelr
Newbie
Karma: +0/-0
Offline
Posts: 2
|
 |
« Reply #770 on: June 10, 2024, 10:48:45 PM »
|
|
|
Oh that fixed her right up! Tune works on a 2003 Audi A4 Quattro Avant. Thank you for your help!
How did you end up fixing it? im having the same issue, i used the v7 stage 1 and log seems stock still. Thanks
|
|
« Last Edit: June 10, 2024, 11:50:05 PM by nathanaelr »
|
Logged
|
|
|
|
nathanaelr
Newbie
Karma: +0/-0
Offline
Posts: 2
|
 |
« Reply #771 on: June 10, 2024, 11:40:13 PM »
|
|
|
only making around 10 psi, not underboosting because it is making the requested but requested is also around 9-10 psi
|
|
« Last Edit: June 10, 2024, 11:49:45 PM by nathanaelr »
|
Logged
|
|
|
|
Breacking
Jr. Member

Karma: +0/-7
Offline
Posts: 31
|
 |
« Reply #772 on: August 10, 2024, 09:31:51 AM »
|
|
|
Good day. I'm trying to activate VVT on an AUDI A4 B5 1.8T 5HP19L. The following maps were found and modified: CDNWS 2 => 3 CWNWSG 0 => 1 CDTENWS 220 => 733 CDTENWS 326 => 745 KFNWSE 18 =. -4 760RM => 4000RM KFNWWLE everywhere 18
Help me find the FNWTME address
Do I need to change more cards to activate VVT?
I changed these maps for tune 06A906032HF and VVT was active
|
|
|
Logged
|
|
|
|
gd_
Newbie
Karma: +0/-0
Offline
Posts: 5
|
 |
« Reply #773 on: February 03, 2025, 12:30:13 PM »
|
|
|
I followed along with overclockedpc's journey from a few years ago regarding tweaking the community file for 91. How did I do? Attached logs for a pull, as well as a stock pull, along with the bin that was flashed.
If you're wondering if I have a FMIC, I don't, this was stock side mount. Its just that they were taken on a 40 degreeF day, IAT's almost never got above 100.
Also, I managed to get my SAI off and passing readiness on my stock BC file, just by making my own XDF for it and zeroing out CDSLS, MSLUB, and MSLBAS. I used the AK file for the tuning part so I could start with the community file without having to do more work on my BC XDF to port everything over, but I can't get SAI to work with it. MSLUB and MSLBAS look fine, but for some reason, the stock & tuned files linked in the OP both already have zero for CDSLS? Is the XDF incorrect? Is 0x181B0 not the correct address? for my BC file its 0x181B3, and all of the xdf's for the AK's on here I keep seeing 0x181B0
|
|
|
Logged
|
|
|
|
gd_
Newbie
Karma: +0/-0
Offline
Posts: 5
|
 |
« Reply #774 on: February 03, 2025, 02:07:26 PM »
|
|
|
I found the issue, the XDF in the first post has CDSLS mapped incorrectly. It is incorrectly mapped as 0x181AD, when CDSLS is actually at 0x181B0. Fixed this and all is good with SAI. I also looked at various XDF's that are floating around here, including the tylerw one, and they're ALL wrong. looks like someone put in the wrong value and everyone just copied it for their XDF.
If you're having problems disabling SAI on the community file or any AK file, and the community stage 1 or tylerw xdf's are all showing 0 instead of 1, update your xdf in tunerpro or download my edited copy. I've uploaded a corrected version, no other changes made.
|
|
|
Logged
|
|
|
|
nyet
|
 |
« Reply #775 on: February 03, 2025, 04:00:35 PM »
|
|
|
looks like someone put in the wrong value and everyone just copied it for their XDF.
Common problem. I have updated the OP accordingly. Thanks!
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
joshuafarwel
Full Member
 
Karma: +10/-1
Offline
Posts: 91
|
 |
« Reply #776 on: February 03, 2025, 06:08:16 PM »
|
|
|
I found the issue, the XDF in the first post has CDSLS mapped incorrectly. It is incorrectly mapped as 0x181AD, when CDSLS is actually at 0x181B0. Fixed this and all is good with SAI. I also looked at various XDF's that are floating around here, including the tylerw one, and they're ALL wrong. looks like someone put in the wrong value and everyone just copied it for their XDF.
If you're having problems disabling SAI on the community file or any AK file, and the community stage 1 or tylerw xdf's are all showing 0 instead of 1, update your xdf in tunerpro or download my edited copy. I've uploaded a corrected version, no other changes made.
Thanks a lot for sharing. I updated it in my big .xdf attached
|
|
|
Logged
|
|
|
|
|