Pages: [1]
Author Topic: 4B0906018AA basic maps defined  (Read 13648 times)
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« on: October 10, 2014, 01:07:38 AM »

This is my first version, all axis definitions come from a 4B0906018P 352750 map pack. Not every axis has the correct adress linked yet, it I find them I will update attached file.
Logged

TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #1 on: November 19, 2014, 03:01:41 PM »

And also in XDF now
UPDATED:
MLHFM adress!! and sorted some maps out.
« Last Edit: December 10, 2014, 06:51:58 AM by TijnCU » Logged

rotax
Newbie
*

Karma: +10/-0
Offline Offline

Posts: 22


« Reply #2 on: June 21, 2016, 09:08:00 AM »

I've been searching for a full xdf och damos file for this ECU with no luck.
Has there been any progress on this xdf-file since it was posted earlier in this thread?

Please share...
Logged
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #3 on: June 22, 2016, 03:24:37 AM »

I have not worked on this ecu anymore, sorry.
Logged

mdz
Full Member
***

Karma: +12/-1
Offline Offline

Posts: 73


« Reply #4 on: June 22, 2016, 08:41:12 AM »

Here's my work in progress. First time defining bin so some axis are missing and some maps may be incorrect. Attached original bin also because it has different software version.  Roll Eyes
Logged
rotax
Newbie
*

Karma: +10/-0
Offline Offline

Posts: 22


« Reply #5 on: June 22, 2016, 01:22:57 PM »

Fantastic work!
Anybody had any success converting .kp files to .xdf files?
Are these maps your guesses or can they be considered as safe (100% correct)?

Thanks again, i'll go ahead and try to convert the maps into a .xdf file...

/D
Logged
mdz
Full Member
***

Karma: +12/-1
Offline Offline

Posts: 73


« Reply #6 on: June 22, 2016, 01:43:53 PM »

Well, I'm complete beginner in all this. I used 225hp TT and many other defined files as a reference to find and compare maps. Maps in folder "Maps" should be right, maps in folder "Unsorted" are the ones i found along the way or the ones I'm not sure. Would be very good if someone with experience would check through it.  Roll Eyes
Logged
marian_gbg
Newbie
*

Karma: +2/-2
Offline Offline

Posts: 17


« Reply #7 on: July 17, 2016, 04:18:59 AM »

Here's my work in progress. First time defining bin so some axis are missing and some maps may be incorrect. Attached original bin also because it has different software version.  Roll Eyes

Are you sure that in LAMFA map (1BD80) "x" and "y" values are correct ?
In the map pack above, LAMFA adres is 1BD94. Who is correct map pack for 018AA ECU with SW 352728 ?
Logged
Jim_Coupe
Hero Member
*****

Karma: +16/-12
Offline Offline

Posts: 663



« Reply #8 on: November 20, 2016, 01:02:00 PM »

Any updates on defs on this ECU?  Hard to find..
Logged

E85oholic
chain_slappinS4
Full Member
***

Karma: +11/-9
Offline Offline

Posts: 58


« Reply #9 on: December 21, 2016, 03:20:27 PM »

Any updates on defs on this ECU?  Hard to find..

heres a damos for a similiar ( how much, not sure ) but its for 4b0906018CM ecu

ive included the hex file and a2l as well as the sgo..
Logged

microsoft asked me to install windows nt or better, so i installed Solaris!!
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #10 on: December 22, 2016, 02:56:09 AM »

Totally different ecu, impossible to compare files.
But thanks for sharing anyway  Wink
Logged

chain_slappinS4
Full Member
***

Karma: +11/-9
Offline Offline

Posts: 58


« Reply #11 on: December 22, 2016, 05:14:02 AM »

Totally different ecu, impossible to compare files.
But thanks for sharing anyway  Wink

Sorry, thought it might be helpful
Logged

microsoft asked me to install windows nt or better, so i installed Solaris!!
Jim_Coupe
Hero Member
*****

Karma: +16/-12
Offline Offline

Posts: 663



« Reply #12 on: December 30, 2016, 12:24:04 PM »

I Added ESKONF to file above.
Logged

E85oholic
marian_gbg
Newbie
*

Karma: +2/-2
Offline Offline

Posts: 17


« Reply #13 on: January 22, 2017, 07:35:11 AM »

This is my repaired XDF for 018AA box with all correct maps needed for stage 1.
Logged
Jim_Coupe
Hero Member
*****

Karma: +16/-12
Offline Offline

Posts: 663



« Reply #14 on: January 22, 2017, 08:29:44 AM »

Nice thanks ill look into it
Logged

E85oholic
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.021 seconds with 17 queries. (Pretty URLs adds 0s, 0q)