Pages: 1 ... 9 10 [11] 12 13 ... 43
Author Topic: Overrun Flames, Gargle, Pop  (Read 360657 times)
Punda
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 32


« Reply #150 on: November 16, 2015, 02:59:02 PM »

works on the 032RP


KFZWMN to -30 on the first 3 columns
CWSAWE to 01
KFZWOP subtracted 20 from 1st column and 5 from 2nd column
KFNWEGM to max rpm

thanks pynoxim for the help with addresses
Logged

"The more you learn, the more you realize you don't know."
vwmaniac
Full Member
***

Karma: +8/-5
Offline Offline

Posts: 169


« Reply #151 on: February 04, 2016, 07:59:38 AM »

works on the 032RP


KFZWMN to -30 on the first 3 columns
CWSAWE to 01
KFZWOP subtracted 20 from 1st column and 5 from 2nd column
KFNWEGM to max rpm

thanks pynoxim for the help with addresses
this works great on my r32 022 906 032eg
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12233


WWW
« Reply #152 on: February 04, 2016, 08:12:50 PM »

KFZWOP subtracted 20 from 1st column and 5 from 2nd column

What is the purpose behind the KFZWOP changes?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
vwmaniac
Full Member
***

Karma: +8/-5
Offline Offline

Posts: 169


« Reply #153 on: February 12, 2016, 04:00:12 PM »

i assumed it was to allow the computer the range to run the negative timing. i don't know that to be true but thats what i make of it. as far as my car goes the minimum timing table in stock form doesn't have a large swing of positive and negative timing so to keep the negative requests in the optimal range they need to be lowered? i dont know...
Logged
contrast
Full Member
***

Karma: +20/-2
Offline Offline

Posts: 215


« Reply #154 on: February 13, 2016, 10:36:59 AM »

In my car KFZWOP wasn't needed.

Regarding KFZWMN load axis, as load is based on MAF and before when I had only two lowest load rows set to -30 I got good bangs when I gently rolled through RPM range. Now I set higher load upwards from 5000 RPM toc-30 too and now it bangs very loudly even when flooring it.
The MAF value doesnt drop in an instant when off throttle, so by the time it reaches lower load column, fuel is gone.
Logged
Sonny
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #155 on: March 12, 2016, 01:53:19 PM »

Hey guys,

can someone pls tell me how to find CWSAWE in 8E0909518AH 366871 (BEX)? Damos or A2L would be great also Wink Cheesy

Thanks and greets,
Sonny

Edit: Some codewords like cwsawe are not easy to find without exact a2l... Or can someone give an advice how to find such short words?
« Last Edit: March 13, 2016, 08:28:25 AM by Sonny » Logged
Sonny
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #156 on: March 20, 2016, 05:54:52 AM »

8E0909518AH 366871 (BEX) attached. Would be great, if someone could tell me how to find CWSAWE in that file.

regards
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1567


« Reply #157 on: March 20, 2016, 06:27:02 AM »

0x11BD2
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1567


« Reply #158 on: March 20, 2016, 06:32:02 AM »

Its easy to find because its next to the ecu number.
Logged
Sonny
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #159 on: March 20, 2016, 06:46:06 AM »

Its easy to find because its next to the ecu number.


Thank you for the fast reply.
But how do you know its not 11BD9 or 11BD3?
Logged
Sonny
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #160 on: March 20, 2016, 07:05:52 AM »

I see...
I think my compared damos differs too much from the file 366871.

thx
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1567


« Reply #161 on: March 20, 2016, 08:26:27 AM »

try and report please
Logged
fknbrkn
Hero Member
*****

Karma: +177/-18
Offline Offline

Posts: 1401


mk4 1.8T AUM


« Reply #162 on: March 20, 2016, 11:00:10 AM »

has anyone monitored real egt with that mod?  Wink
Logged
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2178


« Reply #163 on: March 21, 2016, 12:51:26 AM »

I've thought about this.  Probably through the roof.  But it's reet, everything's still working 10k later.  Turbo has a lovely white dusting on it, probably because it's seen 1000*+.  Meh.
Logged
Rl
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 31


« Reply #164 on: March 21, 2016, 06:06:17 AM »

To everyone having some fun.. how long does your lambdas survive?? Mine after some time throw the "heater circuit" error.. Dont know if the fun worths the lambdas every 3-4 months.. What about your expirience?
Logged
Pages: 1 ... 9 10 [11] 12 13 ... 43
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.129 seconds with 18 queries. (Pretty URLs adds 0s, 0q)