Dev Blog
Forum
Wiki
About
NefMoto
>
Noob Zone
>
Noob Questions
(Moderator:
turboat
) >
Dove straight in
Pages:
1
2
[
3
]
« previous
next »
Author
Topic: Dove straight in (Read 22603 times)
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Dove straight in
« Reply #30 on: December 19, 2014, 02:08:23 PM »
Quote from: AARDQ on December 19, 2014, 09:28:23 AM
I could never get this one (to be clear, 551R running 551S software) into bootmode, either. Tried every trick identified at the time (2012).
Did 3 today
No resistor, no fancy counting. Just ground it, power it up, remove the ground.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
b3n4
Newbie
Karma: +0/-0
Offline
Posts: 23
Re: Dove straight in
« Reply #31 on: December 22, 2014, 08:52:44 PM »
Well I'm pretty jealous of you right now haha. I got a used ECU but am as expected running into IMMO issues. Is the only way to remove the immo to use argdubs tool to flash the eeprom off? Or how is it that the s4 mbox bins do not ask for the immo data is this something that can be coded into the 551R bin as well? Think I may have to bite the bullet and call up the dealer tomorrow.
Thanks again
Logged
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Dove straight in
« Reply #32 on: December 22, 2014, 08:59:19 PM »
Send me the ecu, I will do it for you. Otherwise, just keep trying!
You'll get it.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
b3n4
Newbie
Karma: +0/-0
Offline
Posts: 23
Re: Dove straight in
« Reply #33 on: December 23, 2014, 04:39:43 AM »
I'll pm you. I think the added stress of no backup ecu adds to the frustrations right now
Logged
b3n4
Newbie
Karma: +0/-0
Offline
Posts: 23
Re: Dove straight in
« Reply #34 on: January 17, 2015, 12:57:56 PM »
Hey all dillenger was kind enough to sort out my ECU issue for me. The car is not starting now and continues to just crank over. I checked and its pushing fuel through so that doesnt seem to be an issue. Next thing I was going to check was if its sparking. Whats the best way to check for this?
Thanks
Logged
b4A4nowA6
Full Member
Karma: +1/-4
Offline
Posts: 117
Re: Dove straight in
« Reply #35 on: January 18, 2015, 10:29:56 PM »
Sorry But I just got back on here after taking a couple months break. I have an 03 A6 ME7.1.1
To get the car in boot mode.. USE MPPS......!!!! end of story. Saved my life when all else failed
Logged
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
Re: Dove straight in
« Reply #36 on: January 18, 2015, 10:36:21 PM »
After DD helped me with mine. I could identify my problem as a bad clone cable. When he sent the ecu back I tried my cable to connect with nefmoto and it didnt want to. So i purchased another cable and it works perfect for everything.
Logged
b3n4
Newbie
Karma: +0/-0
Offline
Posts: 23
Re: Dove straight in
« Reply #37 on: January 19, 2015, 09:28:13 PM »
Yea I've been meaning to order a MPPS cable. I used a ross-tech cable in dumb mode seems to work fine. Think what did the first one was loading the wrong bin on then a faulty boot harness. Since getting the car running on the new ECU I can't get the air suspension to work so the cars on the bump stops. I didn't think the ECU was tied to the level controller. But if anyones had experience with having the self level, ESP, and ABS lights all on and can offer soem insite much appriciated.
thanks
Logged
b4A4nowA6
Full Member
Karma: +1/-4
Offline
Posts: 117
Re: Dove straight in
« Reply #38 on: January 20, 2015, 08:19:01 PM »
I don't know what I did , but I used to use vcds in dumb mode.. but now my cabe is dead and not seen by vcds
Logged
b3n4
Newbie
Karma: +0/-0
Offline
Posts: 23
Re: Dove straight in
« Reply #39 on: January 21, 2015, 12:30:36 PM »
That's odd haven't had issues with the Ross-tech cable I know my galleto clone got erased so I had to reset the ftdi numbers
Logged
Pages:
1
2
[
3
]
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> Introductions
=> General Discussion
-----------------------------
Noob Zone
-----------------------------
=> Noob Questions
=> Noob Guides and FAQs
-----------------------------
Technical
-----------------------------
=> NefMoto Software
=> Tuning
===> Documents & Helpers & How To's
===> Community Projects
=> Diagnostics
=> Flashing and Chipping
=> Cluster and Immobilizer
===> ECU EEPROM images
===> Original Cluster dumps
===> Original Cluster dump requests
=> Data Logging
=> Reverse Engineering
=> Communication Protocols
-----------------------------
ECU Files
-----------------------------
=> ECU Definition Files
===> ECU Definition File Requests
=> Original ECU Files
===> Original ECU File Requests
=> Checksum Update Requests
-----------------------------
Vehicles
-----------------------------
=> Vehicle Tech
=> Project Cars
-----------------------------
Regional
-----------------------------
=> Canadian Regional Discussion
=> US Regional Discussion
-----------------------------
Classifieds
-----------------------------
=> For Sale
=> Wanted
=> Services
-----------------------------
Miscellaneous
-----------------------------
=> Off Topic
=> Forum Tech Support
=> Bizarro Messages Posted by Bots and Spammers
Navigation
Home
Help
Login
Register
Personal Tools
November 25, 2024, 02:03:21 PM
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Search
Advanced Search
Loading...
