mrpurple
Newbie
Karma: +0/-0
 Offline
Posts: 6
|
 |
« on: January 22, 2015, 12:37:46 PM »
|
|
|
Hi,
New to this forum and ecus and trying to learn as fast as I can. Got a problem at the moment with reading my ECU through nefmoto software. I can connect to the ECU but am getting decoding not licensed on the DTCs which I think is causing my problem. I have used argdubs software to disable the immo I think correctly by modifying the 95040 0x12 & 0x22 and correcting the checksum by reducing it by 1 on each line. Is there anything else I need to do to enable the ecu to be read on the bench without the clocks attached or furthermore do the clocks need to be somehow deleted from the immo bin? I've done an awful lot of searching and reading and seemed to have got to a point where i'm in need of a shove in the right direction as i'm going round in circles!
Thanks for any help in advance.
Cheers
Bob
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #1 on: January 22, 2015, 12:54:16 PM »
|
|
|
Which ECU?
Also copy paste the output of the nefmoto flasher.
Note that nefmoto's bootmode support is incomplete.
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
mrpurple
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #2 on: January 22, 2015, 01:39:21 PM »
|
|
|
Its a 06A906032HN.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: °6A906032HN 1.8L R4/5VT 06 0001
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Sending start communication request.
Connected
Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Disconnecting because no response was received for the Tester Present message.
Disconnected
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
Also attached are the 95040.bin original and one I created for the immo delete.
I maybe getting my wires a little crossed here so apologies if i'm saying nonsense, but do I need bootmode just to read the flash, I just want to benchread the ECU to have a play about with it before I go and screw one up on a car! It's quite a steep learning curve to get started!
Cheers
Bob
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #3 on: January 22, 2015, 01:48:06 PM »
|
|
|
No, you're on the right track.
You don't need bootmode for reading/writing the flash or reading the eeprom.
You only need bootmode for writing the eeprom.
You can try a lower baudrate...
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
mrpurple
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #4 on: January 22, 2015, 01:51:45 PM »
|
|
|
Tried at all available baud rates at the result is exactly the same output.
Learnt something else along the way through reading with log files so i've attached the full log here if it makes any difference.
Cheers
Bob
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #5 on: January 22, 2015, 01:53:44 PM »
|
|
|
Is the ECU stock?
Also, you can try bootmode read with Galletto...
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
 Online
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #6 on: January 22, 2015, 02:02:03 PM »
|
|
|
you should connect pin #121 with +12v
|
|
|
|
« Last Edit: January 22, 2015, 02:03:50 PM by fukenbroken »
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #7 on: January 22, 2015, 02:09:33 PM »
|
|
|
you should connect pin #121 with +12v
Wait, #121 or #21? I've never powered up #121 |
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
Online
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #8 on: January 22, 2015, 02:33:01 PM »
|
|
|
Wait, #121 or #21?
I've never powered up #121
121 i has the same issue on bench with my 1.8t ecu it wont flash without #121 powered but all ok in boot mode without powering this pin |
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #9 on: January 22, 2015, 02:34:36 PM »
|
|
|
Wait, #121 or #21?
I've never powered up #121
MK4, 121 required  |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
|
nyet
|
|
« Reply #10 on: January 22, 2015, 02:35:42 PM »
|
|
|
Dang I always lose track of these details. Did you already tell me this?
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
mrpurple
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #11 on: January 22, 2015, 04:08:20 PM »
|
|
|
Excellent pin 121 solved the problem, thanks for your help.
Cheers
Bob
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #12 on: January 22, 2015, 04:36:47 PM »
|
|
|
Glad you got your issues sorted!
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
|
