GIAC

Pages: [1]

« previous next »

Author

Topic: GIAC (Read 5448 times)

los93sol

Newbie

Karma: +0/-0
Offline

Offline

Posts: 6

	GIAC « on: July 11, 2011, 09:06:15 AM »

Previously had a GIAC flash on my car and now have a tune from VAST, but I would like to try out some other tunes. That said, I want to backup my VAST tune, but it seems from the GIAC flash that was originally on the ECU that reading has been disabled on my ECU. I even said to hell with it and tried to write it anyways and it still will not work. I read around and saw where it looks like this is common on ECU's that had a GIAC flash in the past and that a workaround was being worked on, is there any way to read this thing out without a Galletto cable? What about overwriting it?


	Logged

Snow Trooper

Hero Member

Karma: +90/-24
Offline

Offline

Posts: 689

	Re: GIAC « Reply #1 on: July 11, 2011, 09:40:07 AM »

I have no issue reading or writing to new and old giac stuff via the nefmoto software. even the encrypted stuff. what I have found works best is to fully reset the ecu power wise. i.e. take the ecu out for a few minutes or disconnect the battery cables for that time. once you power back up go straight into the operation that you want to do and it should work.


	Logged

cartoons?
6A 61 72 65 64 40 76 6C 6D 73 70 65 63

Jason

Hero Member

Karma: +38/-0
Offline

Offline

Posts: 500

Breaks everything!

	Re: GIAC « Reply #2 on: July 11, 2011, 11:07:07 AM »

Some tuners disable the function used to read the tune. Galletto in boot mode or a willem programmer is the only solution I know of. You may be able to use the vag kkl cable and the C167 boot mode tools to do it, but I've never looked into that since I already had a Galletto cable.


	Logged

los93sol

Newbie

Karma: +0/-0
Offline

Offline

Posts: 6

	Re: GIAC « Reply #3 on: July 11, 2011, 11:22:31 AM »

Just tried that and it did change what I was getting, before my logs didn't show anything other than No response to tester present messages, now I am actually getting rejected...here is a log, the full read and memory validation functions are where I fail out.

11/Jul/2011 02:11:06.830: USER: Successfully changed to new communication timings.
11/Jul/2011 02:11:06.834: USER: Requesting security access.
11/Jul/2011 02:11:06.837: LOG: Sent message with service ID SecurityAccess
11/Jul/2011 02:11:06.883: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:06.885: LOG: Received negative response for service ID: SecurityAccess, with response code: GeneralReject
11/Jul/2011 02:11:06.888: USER: ECU reports that security access request was rejected.
11/Jul/2011 02:11:06.891: LOG: Starting diagnostic session type: ProgrammingSession
11/Jul/2011 02:11:06.893: USER: Starting diagnostic session.
11/Jul/2011 02:11:06.895: LOG: Sent message with service ID StartDiagnosticSession
11/Jul/2011 02:11:06.943: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:06.946: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
11/Jul/2011 02:11:06.985: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:06.988: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
11/Jul/2011 02:11:07.025: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:07.027: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
11/Jul/2011 02:11:07.065: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:07.067: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
11/Jul/2011 02:11:07.105: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:07.108: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
11/Jul/2011 02:11:07.141: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:07.143: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
11/Jul/2011 02:11:07.181: LOG: Received message with service ID NegativeResponse
11/Jul/2011 02:11:07.183: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
11/Jul/2011 02:11:07.219: LOG: Received message with service ID StartDiagnosticSessionPositiveResponse


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

June 06, 2025, 05:08:11 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search