dal
Full Member
Karma: +6/-7
 Offline
Posts: 210
|
 |
« Reply #135 on: November 13, 2020, 11:27:36 AM »
|
|
|
Yeah, I tried all related solutions like this.
I solved this with Arduino, its working fine. But if I have a chance to revert to a more OEM solution, I would go for sure.
|
|
|
|
|
Logged
|
|
|
|
|
macxxx
|
|
« Reply #136 on: November 13, 2020, 11:36:15 AM »
|
|
|
So you made a can signal converter?
|
|
|
|
|
Logged
|
|
|
|
dal
Full Member
Karma: +6/-7
Offline
Posts: 210
|
|
« Reply #137 on: November 13, 2020, 11:46:51 AM »
|
|
|
Initially I used an VR to Hall converter, with built-in signal divisor (to calibrate the speed).
Then I spent around 3 months working with arduino and MCP2515 to get the VS from can and generate an square wave signal to the cluster.
My skills with arduino are minimum.
|
|
|
|
|
Logged
|
|
|
|
maj0nez
Newbie
Karma: +0/-0
Offline
Posts: 9
|
|
« Reply #138 on: November 17, 2020, 01:13:45 AM »
|
|
|
Initially I used an VR to Hall converter, with built-in signal divisor (to calibrate the speed).
Then I spent around 3 months working with arduino and MCP2515 to get the VS from can and generate an square wave signal to the cluster.
My skills with arduino are minimum.
Hi You have a sketch for arduino, I will do it on STM32. Best regards |
|
|
|
|
Logged
|
|
|
|
maj0nez
Newbie
Karma: +0/-0
Offline
Posts: 9
|
|
« Reply #139 on: November 24, 2020, 11:38:28 AM »
|
|
|
Hello Auto after SWAP Skoda Octavia 1.8T plus DSG. On the dashboard of the Golf R32 it shows the gear numbers. On the dashboard of the Octavia it does not show.  |
|
|
|
|
Logged
|
|
|
|
veigy
Newbie
Karma: +0/-0
Offline
Posts: 23
|
|
« Reply #140 on: December 01, 2020, 01:06:37 PM »
|
|
|
Hi, I'm looking for some advice. I am trying to install reliable instrument cluster VDO from Audi A6 (4B0920933N) to Audi TT 8N. Almost everything works, but the speedometer shows about 10 km / h less. The pointers are installed correctly. Do anyone know if there is some constant in the EEPROM that could be used to adjust the speed? Thanks
|
|
|
|
|
Logged
|
|
|
|
|
macxxx
|
|
« Reply #141 on: December 01, 2020, 02:22:11 PM »
|
|
|
Does it show 10km/h less in all scale or just in higher speeds?
There are some calibration bytes before speedo map ( 23 1F or something like that ) , but they are covered by checksum so you can't just edit them. Maybe try to copy some parts of a3 8l speedoscale with calibration but from clusters from MY2002 because as your 933N they are crypto.
|
|
|
|
|
Logged
|
|
|
|
veigy
Newbie
Karma: +0/-0
Offline
Posts: 23
|
|
« Reply #142 on: December 01, 2020, 03:28:24 PM »
|
|
|
Thanks for reply, I'll take closer look. In lower speed (city) it is about 5 km/h less. Am I right that I am looking for editing "distance impulse number"?
|
|
|
|
|
Logged
|
|
|
|
veigy
Newbie
Karma: +0/-0
Offline
Posts: 23
|
|
« Reply #143 on: December 02, 2020, 02:20:31 PM »
|
|
|
There are some calibration bytes before speedo map ( 23 1F or something like that )
Which address do you exactly mean by this 23 1F? I found some algorithm to calculate checksum.... |
|
|
|
|
Logged
|
|
|
|
|
macxxx
|
|
« Reply #144 on: December 02, 2020, 04:13:37 PM »
|
|
|
my a6 c5 also had almost 10 km/h difference between speed on cluster and GPS - when higher the speed the more difference it showed , its normal
|
|
|
|
|
Logged
|
|
|
|
veigy
Newbie
Karma: +0/-0
Offline
Posts: 23
|
|
« Reply #145 on: December 02, 2020, 10:52:19 PM »
|
|
|
It is normal when speed on cluster is higher then GPS. In my case is cluster speed about 10-15% lower then GPS and it affects board computer and mileage too....
I compared A6 vs S3 cluster EEPROM and I see some differences in 0x0B4 - 0x0C1 (see picture). Is this what you talking about in previos post? Can I just put these bytes from S3 to A6 eeprom, correct checksum on 0x0B0 and upload it to the cluster?
|
|
|
|
|
Logged
|
|
|
|
|
macxxx
|
|
« Reply #146 on: December 02, 2020, 11:39:54 PM »
|
|
|
Yes try - I was thinking about that area
|
|
|
|
|
Logged
|
|
|
|
maj0nez
Newbie
Karma: +0/-0
Offline
Posts: 9
|
|
« Reply #147 on: December 14, 2020, 03:19:06 AM »
|
|
|
A few dash dump in vageepromer and don't red VIN and other?  |
|
|
|
|
Logged
|
|
|
|
|
macxxx
|
|
« Reply #148 on: December 14, 2020, 03:27:57 AM »
|
|
|
Unknown version propably , then read manually from dump with a hex editor. From which cluster is this dump?
|
|
|
|
|
Logged
|
|
|
|
maj0nez
Newbie
Karma: +0/-0
Offline
Posts: 9
|
|
« Reply #149 on: December 15, 2020, 04:22:53 AM »
|
|
|
EEPROM from Skoda Superb 1.
|
|
|
|
|
Logged
|
|
|
|
|
