Pages: 1 ... 10 11 [12] 13
Author Topic: a3 3.2 022906032CB ME7.1.1G advice  (Read 80289 times)
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #165 on: December 20, 2017, 07:28:12 AM »

If go wot at the first gear then after second gear engage the throttle goes 100% shortly and then ~50% staying there. Does not do this if no wot and no upper gears or using launch. Obviously should log what abs or dsg requests.
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #166 on: January 15, 2018, 07:16:58 AM »

Boring.
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #167 on: February 15, 2018, 11:23:58 AM »

I wake up that fis can be controlled via can. Seems that expensive fis-control is not available and would like to get boost shown. Can I add map sensor to my ECU so that fis-control light could use it?
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #168 on: March 25, 2018, 08:08:20 AM »

Bought 3.25€ arduino nano and 3.38€ mcp2515. MsgID:s 363 and 365 are the line strings, still missing something because shows only if radio on... Can't wait to find the time to finish the code and add boost sensor.
Logged
Jim_Coupe
Hero Member
*****

Karma: +16/-12
Offline Offline

Posts: 663



« Reply #169 on: April 05, 2018, 10:58:55 PM »

Bought 3.25€ arduino nano and 3.38€ mcp2515. MsgID:s 363 and 365 are the line strings, still missing something because shows only if radio on... Can't wait to find the time to finish the code and add boost sensor.

Im back in this thread lol...    Are you gonna send boost to instrument via Ardu nano?
Logged

E85oholic
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #170 on: April 06, 2018, 06:08:25 AM »

Were your 3.2 bottom damaged Jim_Coupe? Yes I send boost to instruments via ardu nano.
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #171 on: April 12, 2018, 12:31:47 AM »

It's summer(tires) again. Logged things, and due to the winter blend of e85 the engine gets ignition retard. But mainly only three cylinders. So there was a thing about these vr engines between banks? One is hotter or what?
Logged
vwdubNam
Jr. Member
**

Karma: +1/-0
Offline Offline

Posts: 27


« Reply #172 on: May 23, 2018, 01:51:58 AM »

It's summer(tires) again. Logged things, and due to the winter blend of e85 the engine gets ignition retard. But mainly only three cylinders. So there was a thing about these vr engines between banks? One is hotter or what?
Thank you for the link, it is going to be an awesome read. i see im not the only one who wants to do this build
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #173 on: June 29, 2018, 11:48:38 AM »

Due to the slipping clutches at gear changes I changed two stage rew limiter (ME7.1 tuning guide/Launch control/Soft limiter) to power cut at gear change. At the stationary limiter I changed driving speed comparing to gear change comparing, at gear change the lower limiter is on at one cycle. It kind of works, bropaply after adjusting limiting rpm it does what is needed i.e. take rews down at gear change.
Logged
prj
Hero Member
*****

Karma: +905/-420
Offline Offline

Posts: 5790


« Reply #174 on: July 02, 2018, 01:04:22 PM »

Have you considered that remapping the gearbox and ECU correctly could be better than random hacks and clutch destruction caused by lack of knowledge? Smiley
Logged

PM's will not be answered, so don't even try.
Log your car properly.
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #175 on: July 02, 2018, 08:48:36 PM »

Yes I have considered. And bropaply could buy remap if it would be feasable and meet my requirements.
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #176 on: July 06, 2018, 05:47:06 AM »

Been having fun  Cool and noticed that the flapped pipe which is used only at boost looks like diesel...
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #177 on: July 17, 2018, 06:31:35 AM »

K1 clutch starts to be done or at least at 14,5bar pressure it hold less than K2 clutch. 200tkm driven.

Intake manifold rejected it's rings, found them laying at the engine bay.
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #178 on: August 19, 2018, 02:09:16 AM »

Got the car back to minor collision repair. Weather no longer above 30 decrees Celsius and boost is back, surely hot weather makes the car slow. Does new OEM clutch hold better than 200tkm driven?
Logged
Mikhail
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 136


« Reply #179 on: December 15, 2018, 12:08:14 PM »

The car desided to become a fwd. Haldex says 16347 EEPROM error. I guess PCB corrosion. Anyone does these at Europe?
Logged
Pages: 1 ... 10 11 [12] 13
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 16 queries. (Pretty URLs adds 0s, 0q)