Pages: [1]
Author Topic: unable to valide memory layout  (Read 8092 times)
mroziu22
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« on: June 14, 2015, 08:06:40 AM »

I cannot read memory layout in my a4 b7 1.8T
I have tried every memory layout, changing boudrate and nothing works. Can someone help to solve it.
Software is 1.9.3.2.
My ECU
Part No SW: 8E0 909 518 AQ HW: 8E0 909 018 B

Below is message from nefmoto


Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Validation failed, ECU reports that security access is not granted.
Memory layout validation failed.
Starting to read data block.
Requesting upload from ECU for address range 0x00800000 to 0x00803FFF.
Request upload from ECU failed, ECU reports security access has not been granted.
Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete.
Finished forcing ECU to recognize that failed read operation is complete.
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
Disconnecting...
Disconnecting because no response was received for the Tester Present message.
Disconnected
Switching to KWP2000 session.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disconnecting because no response was received for the Tester Present message.
Disconnected
Switching to KWP2000 session.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Validation failed, ECU reports that security access is not granted.
Memory layout validation failed.
Starting to read data block.
Requesting upload from ECU for address range 0x00800000 to 0x00803FFF.
Request upload from ECU failed, ECU reports security access has not been granted.
Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete.
Finished forcing ECU to recognize that failed read operation is complete.
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
Logged
h100vw
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 34


« Reply #1 on: July 26, 2015, 11:44:39 PM »

Far from the expert on this? Just curious if the ECU has been flashed previously and security from that tuner is preventing you from reading it?

I have seen this on ECUs I know have been tuned commercially already.

I think if you use the largest memory, then it will handle any of the smaller chips.

Logged
mroziu22
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #2 on: July 27, 2015, 12:12:35 AM »

Job done. Frist is to have good OEM ECU bin file. Just upload it and it goes on. Afterwards I have tried also to put some tuned bin and works well.
Logged
rasima
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #3 on: November 05, 2015, 10:18:55 PM »

Hello Man.

Would you please help how did you resolved it.

Thanks a lot and my regards.
Logged
_nameless
Hero Member
*****

Karma: +320/-445
Offline Offline

Posts: 2654



« Reply #4 on: November 06, 2015, 07:40:36 AM »

Late model b5.5/b6 ecu ask this before reading or writing. As long as you select 800bb you won't have a issue
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 16 queries. (Pretty URLs adds 0s, 0q)