TurboWarrior
Jr. Member
Karma: +0/-0
 Offline
Posts: 44
|
 |
« on: June 29, 2015, 07:12:35 AM »
|
|
|
Hi, what's the best way to setup a work bench outside the cars? I.e what connectors I need ect?
|
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #1 on: June 29, 2015, 08:08:26 AM »
|
|
|
ecu , obd2, psu.
|
|
|
|
|
Logged
|
|
|
|
TurboWarrior
Jr. Member
Karma: +0/-0
Offline
Posts: 44
|
|
« Reply #2 on: June 29, 2015, 09:33:55 AM »
|
|
|
ecu , obd2, psu.
I've got all three.. I've got an old PSU from a computer, What wires am I soldering ect? is there a useful guide I can follow |
|
|
|
|
Logged
|
|
|
|
|
|
TurboWarrior
Jr. Member
Karma: +0/-0
Offline
Posts: 44
|
|
« Reply #4 on: June 29, 2015, 01:24:53 PM »
|
|
|
Cheers does this work with - 06A906018CG - ME3.8.3 IIRC? |
|
|
|
|
Logged
|
|
|
|
turboat
Moderator
Hero Member
Karma: +45/-3
Offline
Posts: 619
|
|
« Reply #5 on: June 30, 2015, 12:24:19 AM »
|
|
|
Yes there is a pin out for m3.8.3 around somewhere, but you cannot read that ecu using the k-line, only write it - although nefmoto doesn't work for that, you need mpps
|
|
|
|
|
Logged
|
|
|
|
TurboWarrior
Jr. Member
Karma: +0/-0
Offline
Posts: 44
|
|
« Reply #6 on: June 30, 2015, 05:35:38 AM »
|
|
|
So how would I edit the existing map on the Ecu it's self?
|
|
|
|
|
Logged
|
|
|
|
|
tjwasiak
|
|
« Reply #7 on: June 30, 2015, 06:40:13 AM »
|
|
|
Desolder, read using programmer, resolder and then flash it as needed.
|
|
|
|
|
Logged
|
|
|
|
TurboWarrior
Jr. Member
Karma: +0/-0
Offline
Posts: 44
|
|
« Reply #8 on: June 30, 2015, 10:06:47 AM »
|
|
|
Desolder, read using programmer, resolder and then flash it as needed.
Hi, what do you mean desolder I'm really new to this and I'm willing to learn.. is there a document I could read? |
|
|
|
|
Logged
|
|
|
|
|
|
TurboWarrior
Jr. Member
Karma: +0/-0
Offline
Posts: 44
|
|
« Reply #10 on: June 30, 2015, 10:37:24 AM »
|
|
|
Ok thanks for that, so how would you read the chip? |
|
|
|
|
Logged
|
|
|
|
|
|
TurboWarrior
Jr. Member
Karma: +0/-0
Offline
Posts: 44
|
|
« Reply #12 on: June 30, 2015, 11:48:55 AM »
|
|
|
This one any good? -http://www.ebay.co.uk/itm/TL866CS-USB-Universal-Minipro-Programmer-EEPROM-FLASH-8051-AVR-MCU-GAL-PIC-SPI-L-/161736984370?pt=LH_DefaultDomain_3&hash=item25a8468732 |
|
|
|
|
Logged
|
|
|
|
TurboWarrior
Jr. Member
Karma: +0/-0
Offline
Posts: 44
|
|
« Reply #13 on: June 30, 2015, 12:04:34 PM »
|
|
|
Would this be fin to act as a powering up for the work bench? if so does anyone no what Wires are what because I ain't got a clue :/ Sorry for the noobie questions! I'm egar to learn   |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #14 on: June 30, 2015, 12:07:48 PM »
|
|
|
Yellow is typically 12V, but you'll want to double check with a volt meter.
Also, a PC supply is probably overkill... you can make do with a 1000mA 12v wall wart.
|
|
|
|
|
Logged
|
|
|
|
|
