|
Jim_Coupe
|
 |
« Reply #15 on: August 19, 2015, 01:08:08 PM »
|
|
|
ESKONF = DEKON? Is this some kind of hardware configuration in the Me7 ?
|
|
|
|
|
Logged
|
E85oholic
|
|
|
|
aef
|
|
« Reply #16 on: August 19, 2015, 11:53:49 PM »
|
|
|
I did a 032HN only with ESKONF lately. N249 and N112 removed  |
|
|
|
|
Logged
|
|
|
|
|
Jim_Coupe
|
|
« Reply #17 on: August 20, 2015, 03:20:57 AM »
|
|
|
Problem is that i cant find where ESKONF is ?
|
|
|
|
|
Logged
|
E85oholic
|
|
|
|
adam-
|
|
« Reply #18 on: August 20, 2015, 03:25:11 AM »
|
|
|
How have you tried to find it? It's literally posted in blind detail all over this site, and its Wiki. Took me 30 seconds to find it in a mates car the other day, and I'm still a "noob"..
If you search the Wiki, it tells you where ESKONF is in relation to other maps. Use the standard 3 bit pairs to search just slightly above the MASSIVE map that is below it, and go from there.
|
|
|
|
|
Logged
|
|
|
|
|
Jim_Coupe
|
|
« Reply #19 on: August 20, 2015, 10:40:47 PM »
|
|
|
Ok I thought it was a sub category to something. Im gonna make a search again on ESKOF and se how I can find it. Thanks for answer
|
|
|
|
|
Logged
|
E85oholic
|
|
|
|
Jim_Coupe
|
|
« Reply #20 on: August 21, 2015, 08:09:34 AM »
|
|
|
Correct me if im wrong.. If i Disable an driver stage "output" (Endstufe) The ECU ignores the diagnosis aswell? Or does this just remove Opecirciut code ?
|
|
|
|
|
Logged
|
E85oholic
|
|
|
|
vwaudiguy
|
|
« Reply #21 on: August 21, 2015, 12:11:54 PM »
|
|
|
Correct me if im wrong.. If i Disable an driver stage "output" (Endstufe) The ECU ignores the diagnosis aswell? Or does this just remove Opecirciut code ?
I believe it does both. Basically you are configuring the ecu hardware-wise using software to tell it that particular system is not present. |
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
|
Jim_Coupe
|
|
« Reply #22 on: August 22, 2015, 10:48:52 AM »
|
|
|
Ahh smart.. Im from the PLC programming world.. now it makes sense to me  |
|
|
|
|
Logged
|
E85oholic
|
|
|
|
aef
|
|
« Reply #23 on: September 01, 2015, 03:26:08 AM »
|
|
|
I did a 032HN only with ESKONF lately. N249 and N112 removed Today the errors came back  17608 P1200-35-00 16795 P0411-35-00 So it looks like "only eskonf" does not work. |
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #24 on: September 01, 2015, 03:50:52 AM »
|
|
|
Is the hardware disconnected?
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #25 on: September 01, 2015, 05:41:47 AM »
|
|
|
yes. from the file: AA FF 00 30 FF F8 30 is now AA FF 00 30 FF FB FC Byte 5= NC NC EKP SLP
Byte 6= ULT UAGR SLV NWS Byte 5=11111000 Byte 6=00110000 is now Byte 5=111110 11Byte 6= 1111 1100 So i changed SLP in Byte 5 and ULT and SLV in Byte 6. SLP=J299 SAI PUMP RELAY
ULT/LDUVS=N249 Schubumluftventil
SLV=N112 SAI RELAY What am i missing? |
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #26 on: September 02, 2015, 11:31:22 PM »
|
|
|
srsly? i try to help here with all the noob threads and give back as much as i can. on the other side i have some threads where i am waiting for answers. mimimi  |
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #27 on: September 02, 2015, 11:54:17 PM »
|
|
|
For SAI, MSLUB needs to be set to 0 too?
|
|
|
|
|
Logged
|
|
|
|
narf0815
Full Member
Karma: +2/-1
 Offline
Posts: 87
|
|
« Reply #28 on: September 03, 2015, 01:37:31 AM »
|
|
|
CDSLS = 0?
MSLUB/MSLBAS = 0?
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #29 on: September 03, 2015, 02:00:50 AM »
|
|
|
Thx i will try.
I was under the impression that ESKONF is kind of a "config" to tell the ecu what is installed.
Looks like this is not enough.
|
|
|
|
|
Logged
|
|
|
|
|
