mkxGTi
Full Member
Karma: +4/-5
 Offline
Posts: 69
|
 |
« on: January 29, 2016, 03:55:31 PM »
|
|
|
So according to this pic:  02 would mean immo is off. Except when the ecu gets plugged in and auto-scan (vagcom) + dtc cleared results in "Engine Start Blocked By Immobilizer" Any suggestions welcome. Using AVDI(real not vvdi/fvdi). and it also swaps the ecu to 02 from 01 but car fails to start :/ I'd like to keep orig bin and not use (generic) from allroad topic post. |
|
|
|
|
Logged
|
|
|
|
jogtx16v
Full Member
Karma: +6/-1
Offline
Posts: 139
|
|
« Reply #1 on: January 29, 2016, 04:09:26 PM »
|
|
|
You forgot to correct checksum bits I think.
|
|
|
|
|
Logged
|
|
|
|
mkxGTi
Full Member
Karma: +4/-5
Offline
Posts: 69
|
|
« Reply #2 on: January 29, 2016, 04:10:44 PM »
|
|
|
 For avdi it appears that the ecu has 01 and both change to 02. Here's full pic of each [immo working]  [immo off-not working]  edit: vehicle would start then shut-off before immo off. Now just cranks but doesn't start. |
|
|
|
« Last Edit: January 29, 2016, 04:41:17 PM by mkxGTi »
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +638/-21
Offline
Posts: 5640
|
|
« Reply #3 on: January 29, 2016, 04:48:35 PM »
|
|
|
Your AVDI is writing to RAM. That is not being committed to the eeprom however. I'd be willing to bet that if you re-read it, no changes are made.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
mkxGTi
Full Member
Karma: +4/-5
Offline
Posts: 69
|
|
« Reply #4 on: January 30, 2016, 04:41:02 AM »
|
|
|
I re-read and changes are there.
|
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +638/-21
Offline
Posts: 5640
|
|
« Reply #5 on: January 30, 2016, 11:41:29 AM »
|
|
|
I'm sure you did. Re-read the ram.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
mkxGTi
Full Member
Karma: +4/-5
Offline
Posts: 69
|
|
« Reply #6 on: January 30, 2016, 04:46:54 PM »
|
|
|
I mean. Connect immo off update confdata. Turn off power.. Re init power and read... Same changes.. Lol maybe i should flash generic file.
Doing this all on bench.
|
|
|
|
|
Logged
|
|
|
|
mkxGTi
Full Member
Karma: +4/-5
Offline
Posts: 69
|
|
« Reply #7 on: February 04, 2016, 06:25:51 PM »
|
|
|
Problem solved.
ddillenger: you were correct in the device writes to ram. Only thing i missed was keeping power on while turning off key-on pwr. The eeprom writes from ram once vehicle is sleeping (a.k.a keys are off).
|
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +638/-21
Offline
Posts: 5640
|
|
« Reply #8 on: February 04, 2016, 06:49:45 PM »
|
|
|
Problem solved.
ddillenger: you were correct in the device writes to ram. Only thing i missed was keeping power on while turning off key-on pwr. The eeprom writes from ram once vehicle is sleeping (a.k.a keys are off).
 I assumed as much. You were writing to ram, but the changes weren't being committed to the eeprom. I could have been clearer with my replies. I apologize for that, but good work! |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
|
H2Deetoo
|
|
« Reply #9 on: February 05, 2016, 03:31:50 AM »
|
|
|
What type of ecu is this?
Rgs H2Deetoo
|
|
|
|
|
Logged
|
|
|
|
mkxGTi
Full Member
Karma: +4/-5
Offline
Posts: 69
|
|
« Reply #10 on: February 05, 2016, 07:21:25 PM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
vwmaniac
Full Member
Karma: +8/-5
Offline
Posts: 169
|
|
« Reply #11 on: February 08, 2016, 08:42:35 AM »
|
|
|
i have had this problem with vag commander. it will edit the data but as its only committed to ram it is not stored. you need to do read and write in bootmode. i have also noticed that reading the eerpom in vag commander has yielded some interesting result, mostly not all of the data is read.
|
|
|
|
|
Logged
|
|
|
|
mkxGTi
Full Member
Karma: +4/-5
Offline
Posts: 69
|
|
« Reply #12 on: February 08, 2016, 06:08:48 PM »
|
|
|
What "vag commander" are you using? Reason not all data is read is because they thought it was a fantastic idea to bend ppl over to get as much cash as possible (special functions.. You need 3 to use one properly)
|
|
|
|
|
Logged
|
|
|
|
vwmaniac
Full Member
Karma: +8/-5
Offline
Posts: 169
|
|
« Reply #13 on: February 09, 2016, 10:04:35 AM »
|
|
|
What "vag commander" are you using? Reason not all data is read is because they thought it was a fantastic idea to bend ppl over to get as much cash as possible (special functions.. You need 3 to use one properly)
the free one i downloaded. really only use it to retrieve security login codes. i have 2.5 and 5.1 i believe. |
|
|
|
|
Logged
|
|
|
|
mkxGTi
Full Member
Karma: +4/-5
Offline
Posts: 69
|
|
« Reply #14 on: February 09, 2016, 07:40:46 PM »
|
|
|
Using real tool (latest). Clones only go so far and the ones i've seen (5.x) do not work well if at all.
|
|
|
|
|
Logged
|
|
|
|
|
