Pages: [1]
Author Topic: Help understanding CAN wake up to Audi A3 cluster  (Read 3908 times)
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21


« on: October 17, 2021, 11:18:04 AM »

Hi,

I've been attempted to get an A3 cluster powered up on the bench (8P0920981F) but I'm struggling to get my head around the wiring. I have a CANanylst-ii CAN to USB tool but I don't understand how it's meant to be wired.

On the dash you have CAN H & L on pins 29 & 30 which I assumed went to the CANusb but CAN wakeup line is on pin 5 of the dash which I guess is where the signal needs to be sent but not sure how to wire it?



Thanks
Logged
macxxx
Sr. Member
****

Karma: +29/-1
Offline Offline

Posts: 498


« Reply #1 on: October 17, 2021, 01:40:16 PM »

send it just on CAN H & CANL
Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21


« Reply #2 on: October 18, 2021, 05:44:06 AM »

For some reason it's not working. I don't really know enough to figure out why  Undecided
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1566


« Reply #3 on: October 18, 2021, 05:48:59 AM »

which software is this? i am unable to find it by just googling the header text...

can you provide a link please
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #4 on: October 18, 2021, 06:15:39 AM »

which software is this? i am unable to find it by just googling the header text...

can you provide a link please
You get this software with CANalyst-II device

For some reason it's not working. I don't really know enough to figure out why  Undecided
I never worked with 8P, but on B6/B7 you receive some data from cluster on CAN lines
Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21


« Reply #5 on: October 18, 2021, 07:16:05 AM »

Yes it's just software that came with the device.

Not receiving anything but I guess it's because the cluster needs to be woken up first on the wake up pin 5? 
Logged
macxxx
Sr. Member
****

Karma: +29/-1
Offline Offline

Posts: 498


« Reply #6 on: October 18, 2021, 12:14:39 PM »

You have gateway connected? Maybe try to send the frames on Convienence CAN. Are you sure the frame is correct?

I had no problem with starting A6 C6 cluster on table with can frames , I never tried A3 8P with can frame because I had a setup with bordnetz and gateway - if I will find some time I will try to start it using can frames.
Logged
cherry
Full Member
***

Karma: +23/-2
Offline Offline

Posts: 245


« Reply #7 on: October 18, 2021, 01:35:42 PM »

Are you sure with the message you send? Normally it´s 07 07 00 00 00. Check also your CAN termination, maybe you need to add a resistor if cluster and tool does not have inside.
Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21


« Reply #8 on: October 18, 2021, 03:42:44 PM »

apparently ID:575 DLC:2 DATA: 07 00
Logged
simple2me
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 28


« Reply #9 on: October 22, 2021, 06:09:17 AM »



I never could get software for the one i bought. took me to some website which would never give me download link. you have link for software. mine is just sitting in the box since i bought another tool.
« Last Edit: October 22, 2021, 06:11:09 AM by simple2me » Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21


« Reply #10 on: October 22, 2021, 08:26:06 AM »


I never could get software for the one i bought. took me to some website which would never give me download link. you have link for software. mine is just sitting in the box since i bought another tool.

Mine didn't come with any but this is what I managed to find..

https://easyupload.io/ljo2ha
Logged
simple2me
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 28


« Reply #11 on: December 22, 2021, 06:17:24 AM »

just seeing your reply. no file found on the link.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.036 seconds with 17 queries. (Pretty URLs adds 0s, 0q)