andrew
Newbie
Karma: +0/-0
 Offline
Posts: 10
|
 |
« on: March 03, 2016, 11:14:20 AM »
|
|
|
Hello, does somebody knows or can point to way to enable/modify/or put ECU values into its can-messages ?
.. like Boost (vag can-id 0x555) which is available not in all turbo MED9x
thanks
|
|
|
|
« Last Edit: March 03, 2016, 12:59:38 PM by andrew »
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
Offline
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #1 on: March 03, 2016, 12:38:03 PM »
|
|
|
yes, they are stored in ram locations
so any tweaks available here
|
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #2 on: May 16, 2016, 05:46:12 PM »
|
|
|
Hello, does somebody knows or can point to way to enable/modify/or put ECU values into its can-messages ?
.. like Boost (vag can-id 0x555) which is available not in all turbo MED9x
thanks
There is a function read the FR it's called embassies iirc |
|
|
|
|
Logged
|
|
|
|
nihalot
Full Member
Karma: +41/-3
Offline
Posts: 117
|
|
« Reply #3 on: July 13, 2016, 01:53:53 AM »
|
|
|
hey
did you have any success in adding boost pressure 0x555 to canbus??
regards
|
|
|
|
|
Logged
|
www.tangentmotorsport.commultimap/LC/rolling antilag for MG1/MED17/EDC17/MED9/EDC15 contact for reverse engineering services of any ECU/TCU
|
|
|
jochen_145
Full Member
Karma: +9/-4
Offline
Posts: 177
|
|
« Reply #4 on: September 12, 2017, 05:55:27 AM »
|
|
|
Same question again: I like to activate Motor_07 and Motor_05 message on CAN-bus of a MK1 Audi TT with ME7.5 Taking a look into FR, the activation should be done by CW_CAN_S, witch should be a 16bit binery value. A2L tells differend, CW-CAN_S are 4 times awailible but only in 8bit size.. But all CW_CAN_S values are set to 0xff, so at the end, all CAN-values are enabled. But why are they not on CAN-bus ? yes, they are stored in ram Locations so any tweaks available here So I Need to tweak E2 to activiate Motor_05 and Motor_07 too ? Could this be done by coding ? Anyone ever worked on this and can give advice ? BR |
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
Offline
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #5 on: September 12, 2017, 06:01:20 AM »
|
|
|
there is no way to add this by coding
|
|
|
|
|
Logged
|
|
|
|
jochen_145
Full Member
Karma: +9/-4
Offline
Posts: 177
|
|
« Reply #6 on: September 12, 2017, 08:30:16 AM »
|
|
|
 any other idea to active the Motor_07 message ? In FR, there seems also a value SY_CAN_Config responcible for different kind of CAN Messages. But I cannot find SY_CAN_Config in A2L .. No more idea yet, CW_CAN_S should be the right value, but this seems not to work, or got the wrong address in A2L |
|
|
|
|
Logged
|
|
|
|
|
nubcake
|
|
« Reply #7 on: September 19, 2017, 02:52:16 AM »
|
|
|
any other idea to active the Motor_07 message ? In FR, there seems also a value SY_CAN_Config responcible for different kind of CAN Messages. But I cannot find SY_CAN_Config in A2L .. No more idea yet, CW_CAN_S should be the right value, but this seems not to work, or got the wrong address in A2L SY_CAN_Config is a compile-time option, can't be changed in a "ready" binary. CW_CAN_S won't do that either. You have to research the format of said CAN frame (FR should have this info), then disassemble the binary to find where CAN communication is, then manually add the code for filling out and sending said message. Not an easy task, but totally doable. |
|
|
|
|
Logged
|
|
|
|
jochen_145
Full Member
Karma: +9/-4
Offline
Posts: 177
|
|
« Reply #8 on: September 20, 2017, 02:39:13 AM »
|
|
|
SY_CAN_Config is a compile-time option, can't be changed in a "ready" binary. Thanks, this is the info I was missing and I don´t want do read An new compilation is not a task of mine, so no Motor_07 message availibe on my ECU.. Good to know for someone else, who has the same idea and is looking for that info |
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
Offline
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #9 on: September 27, 2017, 10:04:52 AM »
|
|
|
there is 2 or 3 unused bytes in ecu outgoing can-bus messages any value can be added here if you good with ida things  |
|
|
|
|
Logged
|
|
|
|
jochen_145
Full Member
Karma: +9/-4
Offline
Posts: 177
|
|
« Reply #10 on: September 30, 2017, 01:59:41 AM »
|
|
|
I never worked on this yet.. IDA-things normaly needs new compilation and if you need to re-compile, you can also active Motor_07 ID AFAIK. As long as it needs to have a new complilation for that function, I am out so fare btw and a bit OT.: I know for other SW, if you re-compile, you will get new addresses and a new *.A2L. If someone chance the ME7 Software with some additional code, I expact the same, and original A2L or Damos wil not work.. Am I true with this ? |
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #11 on: September 30, 2017, 04:39:49 AM »
|
|
|
I never worked on this yet.. IDA-things normaly needs new compilation and if you need to re-compile, you can also active Motor_07 ID AFAIK. As long as it needs to have a new complilation for that function, I am out so fare btw and a bit OT.: I know for other SW, if you re-compile, you will get new addresses and a new *.A2L. If someone chance the ME7 Software with some additional code, I expact the same, and original A2L or Damos wil not work.. Am I true with this ? You either: a) Have source code for ME7, which I doubt or b) Couldn't hack your way out of a paper bag and need to do some serious reading. |
|
|
|
|
Logged
|
|
|
|
jochen_145
Full Member
Karma: +9/-4
Offline
Posts: 177
|
|
« Reply #12 on: September 30, 2017, 07:19:52 AM »
|
|
|
You either: Ehmm yes, that is what I worte I know for other SW, if you re-compile, you will get new addresses and a new *.A2L.
If someone chance the ME7 Software with some additional code, I expact the same, and original A2L or Damos wil not work.. can confirm to this ? |
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
Offline
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #13 on: September 30, 2017, 10:08:59 AM »
|
|
|
ida is not compiler but dissasembler
and again you cant compile whole binary if you havent sources for that
with ida you can understand how the ecu handles can-bus data, write some code in asm, compile it and change/add it in your file thru hex editor
|
|
|
|
|
Logged
|
|
|
|
jochen_145
Full Member
Karma: +9/-4
Offline
Posts: 177
|
|
« Reply #14 on: October 01, 2017, 09:36:06 AM »
|
|
|
Thanks again for your explanation Ok, if I unterstand you right, you just wirte your own code, compile and add the code in hex via editor to the original code. (so, you A2L will not change in this case, good to know !) But I also need to twique the original code, to jump into the new code and jump back to original, witch will be also done in hex-editor, base on the research of IDA?! At the end, if you allready have your own code or twique the original code to use unused space in e.g. Motor_06, Byte 6 (0x488), I can take over this hex-code via hex-editor in my APP software ? I think CAN-haendler will be the same in all software... |
|
|
|
|
Logged
|
|
|
|
|
