Pages: [1]
Author Topic: 8N0906018AB - 002 - Flasher - THIS IS THE RAM  (Read 6574 times)
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 157


« on: January 27, 2023, 12:29:02 PM »

Hello everyone ... i got a ECU there


I connect the ECU to the Flasher works fine, but if i try to read the ECU nefmoto say´s - THIS-IS-THE-RAM and wont let me read.

I i try to read it with Magic Motorsport it works on Boot Mode. Other flashtools like Kess V2 - V3 does the same thing.

When i cycle the power it return the 8N0906018AB Number if i try to flash i does not respond, then i try a "Read of Information" again
then i comes "THIS IS THE RAM" ... someone had this issue before?

The RAM message comes everytime after i try to flash the ecu on bench.

i provide the pictures and the files - even with ori file same fault.


after picture 6 i can just cycle the ecu to go back to get the informations back from the ecu.



Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12276


WWW
« Reply #1 on: January 27, 2023, 12:49:50 PM »

flash is bad.

bootmode it to stock. Anything else is a waste of time.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 157


« Reply #2 on: January 27, 2023, 02:18:59 PM »

flash is bad.

bootmode it to stock. Anything else is a waste of time.

it is in Stock sorry for my conversation little bit complex to discribe Smiley

Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12276


WWW
« Reply #3 on: January 27, 2023, 02:58:55 PM »

Do you have a spare ECU you can flash it to?

Could be the ECU HW, could be not supported by NEF.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1426



« Reply #4 on: January 28, 2023, 03:18:26 AM »

Use mpps on 512 kb ecus
Logged
overspeed
Sr. Member
****

Karma: +21/-5
Offline Offline

Posts: 388



« Reply #5 on: January 28, 2023, 04:53:41 AM »

You can´t flash with nefmoto in bench, only OBD AFAIK

Kess/Ktag and Magic can only boot... MPPS can Bench flash those
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12276


WWW
« Reply #6 on: January 29, 2023, 05:44:46 PM »

You can´t flash with nefmoto in bench, only OBD AFAIK

untrue, you can flash with nef on the bench just not boot mode

the problem with bench flashing non-boot mode is immo, not nef.
« Last Edit: January 29, 2023, 08:36:38 PM by nyet » Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2809



« Reply #7 on: January 29, 2023, 07:52:08 PM »

You can´t flash with nefmoto in bench, only OBD AFAIK

Kess/Ktag and Magic can only boot... MPPS can Bench flash those
Mpps does bootmode just fine too just so you are aware...
Logged

Giving your mom a tuneup
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 157


« Reply #8 on: January 30, 2023, 10:08:53 AM »

I can do it on KTag - Bootmode, Kess v3 boot/bench/obd and mms only boot.

there is no problem with bootmode but if i try it via obd2 with ori file with kess v3, Ktag bench, or Nefmoto via Bench its not working
but its a ori file there is nothing modifyd inside ... the ecu goes every try of flashing in RAM MODE .... Boot it works ...

I done immo off but car also dont start but the ecu matches to the other ecu that i buy.... something really strange is going on on this ecu what i
have buy
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 157


« Reply #9 on: January 30, 2023, 10:17:34 AM »

Do you have a spare ECU you can flash it to?

Could be the ECU HW, could be not supported by NEF.


sure i got many ^^ some BAM ECU´s and the lower one

But the flasher worked all the time now i got 2 ECU´s that dont work :< The one dont leave the programming session
and the other one you saw in my post :< sure i got backup tools thats not the problem but with nef it works easy asf no stupid
clicks for downloading files.... diffwrite and so on..
Logged
prj
Hero Member
*****

Karma: +1072/-491
Offline Offline

Posts: 6059


« Reply #10 on: January 30, 2023, 10:26:42 AM »

I wonder if it's another case of frying the ECU's one after another.
When you put ECU in bootmode, describe exactly the process.
1. Do you switch the positive or the negative on/off?
2. Do you use a resistor when grounding the flash pin?
Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 157


« Reply #11 on: January 31, 2023, 02:03:02 AM »

I wonder if it's another case of frying the ECU's one after another.
When you put ECU in bootmode, describe exactly the process.
1. Do you switch the positive or the negative on/off?
2. Do you use a resistor when grounding the flash pin?


Bootmode is handeld by device -> MMS , KTag, KessV3 so the device is pulling down

and switching is automatet by device but in nefmoto i do it via Powersupply positive evertime it works without problem
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 157


« Reply #12 on: January 31, 2023, 02:06:42 AM »

I wonder if it's another case of frying the ECU's one after another.

There is no rip of ECU only that one

Only the one control unit that I bought has the phenomenon that it always goes into RAM mode, regardless of whether it is with the original software and IMMO or with a modified file... The control unit that I am describing here goes into the program from RAM even in its original state after trying to start.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.021 seconds with 17 queries. (Pretty URLs adds 0s, 0q)