|
Title: Timing retards bam 1.8 Post by: pathanas on September 04, 2018, 10:47:50 PM Hello,I am working on my audi tt 1.8 and getting some retards on high RPM.
My trims are near 1 on idle and part Is that from knock sensor voltages? Title: Re: Timming retards bam 1.8 Post by: aef on September 05, 2018, 04:34:57 AM upload the untouched csv ::)
Title: Re: Timming retards bam 1.8 Post by: pathanas on September 05, 2018, 04:54:43 AM ΟΚ
Title: Re: Timming retards bam 1.8 Post by: spacey3 on September 05, 2018, 05:04:45 AM What did you use to log? The logfile is pretty awful.
Retard doesn't look that bad though, just pull a bit of timing...? Boost is way over the map sensor also I see... Title: Re: Timming retards bam 1.8 Post by: pathanas on September 05, 2018, 06:09:57 AM I used me7 logger.that is my first log :)I was using vag com
A have a gtx2867 and on this log I am hitting 30,5 psi of boost on 7200rpm. I was thinking to enrich a little on red line to avoid the retard corrections at first...? Title: Re: Timming retards bam 1.8 Post by: pathanas on September 05, 2018, 06:26:05 AM I just trying to find the reason of that retard,the knok voltages are not more than 30v EGT and IAT are not too high.
Title: Re: Timming retards bam 1.8 Post by: nyet on September 05, 2018, 08:44:37 AM Why are your separators ; and not commas?
A lot of those values are plain wrong, are you sure you are using the right .ecu definition for your bin? Title: Re: Timming retards bam 1.8 Post by: adam- on September 05, 2018, 09:36:26 AM It's been editted/cut. I bet foreign/incorrect CSV format.
Title: Re: Timming retards bam 1.8 Post by: pathanas on September 05, 2018, 09:59:45 AM The file is exactly how it's been saved from logge, I did only delete the first lines information
On the ecu definitions for the ecu do you mean these I am using on winols? In order to create the tamplate file I used the modified bin Title: Re: Timming retards bam 1.8 Post by: nyet on September 05, 2018, 10:52:22 AM The file is exactly how it's been saved from logge, I did only delete the first lines information Please do NOT UPLOAD EDITED CSVsQuote On the ecu definitions for the ecu do you mean these I am using on winols? In order to create the tamplate file I used the modified bin The values you are logging are very wrong. Something is amiss. Title: Re: Timming retards bam 1.8 Post by: pathanas on September 05, 2018, 11:18:40 AM What do you mean by edited cvs?
What was edited? Title: Re: Timming retards bam 1.8 Post by: nyet on September 05, 2018, 12:17:48 PM What do you mean by edited cvs? What was edited? I did only delete the first lines information Title: Re: Timming retards bam 1.8 Post by: aef on September 05, 2018, 12:47:41 PM only use ecuxplot to open the logs and nothing more
not necessary to delete something from the file Title: Re: Timming retards bam 1.8 Post by: pathanas on September 05, 2018, 01:00:22 PM only use ecuxplot to open the logs and nothing more not necessary to delete something from the file ok thank you, i will try again Title: Re: Timming retards bam 1.8 Post by: nyet on September 05, 2018, 01:09:05 PM I bet foreign/incorrect CSV format. Yea, for languages that use commas instead of decimal places, csvs end up semi-colon separated. In any case, that isn't a problem, ECUxPlot can handle semicolons. the problem is most of the values logged are completely wrong. Title: Re: Timming retards bam 1.8 Post by: pathanas on September 24, 2018, 12:31:05 PM here is my log, all the problem was the windows regional setting and nothing else
Title: Re: Timing retards bam 1.8 Post by: nyet on September 24, 2018, 03:05:33 PM Are you kidding me? You are going to grenade your turbo if not your motor. You are boosting way past the MAP limit.
And you aren't logging anywhere near the things needed. Not even req boost? WGDC? WTF? Title: Re: Timing retards bam 1.8 Post by: pathanas on September 24, 2018, 07:52:00 PM EBC is the reason and not doing the pressure reading 5120 hack is the answer...but lets come back to the first question of that post finally: the ignition corrections. Due to iat , high knock voltages?
Title: Re: Timing retards bam 1.8 Post by: nyet on September 24, 2018, 08:54:56 PM -4 is not a lot of retard. Pull 4 deg timing req 4750 rpm and up, and get rid of that spike at 4800, or pull some boost. No way of knowing which makes more power w/o a dyno.
Ideally you really should consider 5120. |