NefMoto

hi gents.

After i read some different threads regarding this issue without getting a prober answer to my question I thought I would start a new thread.

I tried to do my first modified BIN file, I now Winols tells me i have a 78% original file, I should have changed parameters for DSG to manual, SAI Off, Evap Off, Cat off, Post Lambdas Off.

I know there probadly would be alot more work to be done in the ECU, but for now i think I would try to correct checksum and write to ECU again to if my changes work.

I have Winols testversion, Tunerpro 5.00 and MPPS V18 Clone. Is there any of these programs there will help me in correct checksum ? I can understand none of the checksumstools in here would work on a ME7.1.1 ST10, right?

again all thoughts a appreciated, i'm here to learn.

Hummel

http://www.mtx-electronics.com/prodotti/Software:tunerpro-checksum-plugins

I'd be surprised if that plugin worked for the ST's. See attached. This should be good, but I have no way to verify right now. Make sure you have a full backup.

the early version of winols floating around has checksums for st10 bundled

Can't get Tunerpro to recognize those plug-ins. Was hoping to compare the cs'd files. Did anyone else get that working? Copied the .dll's, along with the registration keys into the plug-ins folder, but they dont show under the help menu in Tunerpro.

I read something about an early Winols could do the job (1.5?). But I couldn't find it, I guess I need to search a bit more...

MPPS V18 says something about it will calculated checksum, but I dont know if I can count on that, anyone tried it ?

vwaudiguy: When you say a full backup? What do I need to do then ? Sorry for my Noobiness...

Having a way to recover in boot mode in case the checksum wasn't done correctly. Ideally you want to have a complete back up of everything unique to the ecu. The ST-10's have data stored in the processor, as well as the flash, and the eeprom. Backup all 3.

I Only have MPPS to read and Write and I read a full data via MPPS. I cannot read the EEPROM, tried already and ended up sending it out to a guy who could do IMMO off.


MPPS told me it had corrected 6 checksum files, but I'm a bit afraid to write to the ECU. could any one compare checksums on these two files?
 The Data only is the original file.

 ;)

Thank you aef.

Now i tried to Write to the ECU, without success  :-[  I believe I now have a empty flash and when I try to write the new file I says requested time delay not met.

Do I need to bring the ECU in boot mode before I write to it ?

Anyone else have experience with MPPS V18 and/or ME7.1.1

Thanks

If you are not able to write it via obd you will have to boot.

there are various threads about theses ecus, mostly mk5 r32, not save to write via obd.

try to boot it and use the generic protocols in mpps18

Success :) I managed to write to the ECU via OBD. I couldn't find the generic section in my MPPS V18, maybe because its a clone ? After a few attempts in boot mode and not in bootmode, it suddenly start writing and I managed to write my Modified file to the ECU.  ;D Happy days.

Until I started the car and I still had the EVAP, SAI and rear O2 sensor faults, but I could Code the software from DSG to manual with sucess, so thats good!... Okay, I studied wiki through again and I don't think I had the ESKONF part right for the EVAP, SAI and O2 sensors.

Before I try to write to my ECU again, could someone maybe check my file, at least the checksum? My goal with this is to remove the MIL ON faults, and I have completely removed both rear O2 sensors, EVAP system, SAI system, DSG gearbox.

Thanks guys!

And my file... ;D