|
Title: Reading MK1 TT cluster Post by: BlackT on February 04, 2019, 01:59:59 AM Hello,
I want to get PIN from TT cluster so i can instal it in car. The cluster is 2003, and car is 2001. I need PIN so I can login in with VCDS and pair it to immo of the car. But I am not able to read PIN with vag-comander (https://i.postimg.cc/JnNptsH6/TTcluster.png) (https://postimages.org/) Is there any advice from you? Is ther any other program that can read this cluster? Title: Re: Reading MK1 TT cluster Post by: mushtafa on February 04, 2019, 02:21:49 AM I have no experience with the TT, but if you click on the Instrument/Immobiliser button, read the EEPROM, it should display the mileage and PIN
Title: Re: Reading MK1 TT cluster Post by: BlackT on February 04, 2019, 02:36:31 AM I know but it doesen't read correct
(https://i.postimg.cc/50dNJ2zN/TTcluster2.png) (https://postimages.org/) Forget to mention, i use only K-line, but I think connecting to can-bus wouldn't make any difference. Title: Re: Reading MK1 TT cluster Post by: macxxx on February 05, 2019, 05:28:52 AM Its a jeager MM - commander cannot read it , try vagtacho maybe
Title: Re: Reading MK1 TT cluster Post by: BlackT on February 05, 2019, 09:50:06 AM Is it possible to use Vag tacho software with commander cable, or KKL, or galleto 1260, or VCDS 11?
Title: Re: Reading MK1 TT cluster Post by: roverguy7 on February 05, 2019, 10:07:29 AM I was able to read an 04 mk1 tt Jeager MM cluster with Commanderand KKL cable. I had to use Shadow1 for it to pull and it pulled a full 10000 blocks, but listed immo and vin where it was supposed to in the dump.
Title: Re: Reading MK1 TT cluster Post by: Black_A4 on February 06, 2019, 12:42:03 AM Is there a proper tool availible which can read and write those clusters?
Title: Re: Reading MK1 TT cluster Post by: aef on February 06, 2019, 01:11:41 AM carprog from codecard.eu
Title: Re: Reading MK1 TT cluster Post by: Black_A4 on February 06, 2019, 03:47:06 AM An X-Prog Clone can not be used?
Title: Re: Reading MK1 TT cluster Post by: aef on February 06, 2019, 03:53:40 AM letmegooglethatforyou
lazy germans ::) Title: Re: Reading MK1 TT cluster Post by: BlackT on February 06, 2019, 04:13:10 AM carprog from codecard.eu Is there anything cheaper? I was able to read an 04 mk1 tt Jeager MM cluster with Commanderand KKL cable. I had to use Shadow1 for it to pull and it pulled a full 10000 blocks, but listed immo and vin where it was supposed to in the dump. Tryed that no luck, direct MM reset cluster and after that commander shuts downTitle: Re: Reading MK1 TT cluster Post by: Nothery1952 on February 24, 2019, 03:03:45 AM Search for the pattern AUZ* @eeprom mapping location between 0x3800 and 0x3FFF. The two bytes before the search pattern is your pin. For example
@0x3B90 FF FF FF FF FF 02 18 F4 41 55 5A 35 5A 30 42 39 -> ÿÿÿÿÿ..ôAUZ5Z0B9 0x18F4 coverted to decimal should be 6388. Don´t forget the leading zero that means you have to enter 06388 That´s all! Sorry I´m to lazy to upload a picture. ;) Title: Re: Reading MK1 TT cluster Post by: BlackT on February 24, 2019, 03:24:30 AM Vag comander read eeprom only to 0x200 adress :-\
Title: Re: Reading MK1 TT cluster Post by: roverguy7 on February 25, 2019, 10:03:03 AM I would try a few more times with commander. I was able to get one to read, but it did take a few attempts. Try with both Shadow1, and MM Direct. I ran into an error one time when I didn't run commander with administrator privileges.
Title: Re: Reading MK1 TT cluster Post by: b62.7t on February 27, 2019, 12:54:24 AM I just did this, I got a MK1 TT with the MM, I used vag comander and tried all thre options for the MM. MM direct pulled the whole thing then tried what Nothery1952 posted and it worked.
Title: Re: Reading MK1 TT cluster Post by: Black_A4 on February 27, 2019, 07:12:37 AM lazy germans ::) I am not to lazy just found different statments Title: Re: Reading MK1 TT cluster Post by: BlackT on February 27, 2019, 09:21:43 AM I just did this, I got a MK1 TT with the MM, I used vag comander and tried all thre options for the MM. MM direct pulled the whole thing then tried what Nothery1952 posted and it worked. does your cluster gets turn off when you pulling epprom via MM direct?Title: Re: Reading MK1 TT cluster Post by: b62.7t on February 27, 2019, 03:50:58 PM No but it did beep and reset. I used Vag Commader 1.4 and had to run an emulation of windows xp on my windows 10 pc because windows 10 was not laking it.
Title: Re: Reading MK1 TT cluster Post by: BlackT on February 27, 2019, 11:47:21 PM I have borh XP and windows 7. When I go direct MM the cluster goes beep rhen resets. But the can commander on PC shots down. Samo on XP,same on win7
Title: Re: Reading MK1 TT cluster Post by: roverguy7 on March 01, 2019, 10:20:16 AM I used Commander 2.5 and a generic KKL cable on a Windows 10 machine, worked well for me.
|