Pages: [1] 2
Author Topic: Reading MK1 TT cluster  (Read 11501 times)
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425



« on: February 04, 2019, 01:59:59 AM »

Hello,
I want to get PIN from TT cluster so i can instal it in car. The cluster is 2003, and car is 2001. I need PIN so I can login in with VCDS and pair it to immo of the car.
But I am not able to read PIN with vag-comander

Is there any advice from you? Is ther any other program that can read this cluster?
Logged
mushtafa
Full Member
***

Karma: +3/-4
Offline Offline

Posts: 121


« Reply #1 on: February 04, 2019, 02:21:49 AM »

I have no experience with the TT, but if you click on the Instrument/Immobiliser button, read the EEPROM, it should display the mileage and PIN
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425



« Reply #2 on: February 04, 2019, 02:36:31 AM »

I know but it doesen't read correct


Forget to mention, i use only K-line, but I think connecting to can-bus wouldn't make any difference.
Logged
macxxx
Sr. Member
****

Karma: +30/-1
Offline Offline

Posts: 498


« Reply #3 on: February 05, 2019, 05:28:52 AM »

Its a jeager MM - commander cannot read it , try vagtacho maybe
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425



« Reply #4 on: February 05, 2019, 09:50:06 AM »

Is it possible to use Vag tacho software with commander cable, or KKL,  or galleto 1260, or VCDS 11?
Logged
roverguy7
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #5 on: February 05, 2019, 10:07:29 AM »

I was able to read an 04 mk1 tt Jeager MM cluster with Commanderand KKL cable. I had to use Shadow1 for it to pull and it pulled a full 10000 blocks, but listed immo and vin where it was supposed to in the dump.
« Last Edit: February 05, 2019, 11:43:52 AM by roverguy7 » Logged
Black_A4
Full Member
***

Karma: +1/-1
Offline Offline

Posts: 51


« Reply #6 on: February 06, 2019, 12:42:03 AM »

Is there a proper tool availible which can read and write those clusters?
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601


« Reply #7 on: February 06, 2019, 01:11:41 AM »

carprog from codecard.eu
Logged
Black_A4
Full Member
***

Karma: +1/-1
Offline Offline

Posts: 51


« Reply #8 on: February 06, 2019, 03:47:06 AM »

An X-Prog Clone can not be used?
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601


« Reply #9 on: February 06, 2019, 03:53:40 AM »

letmegooglethatforyou
lazy germans  Roll Eyes
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425



« Reply #10 on: February 06, 2019, 04:13:10 AM »

carprog from codecard.eu
Is there anything cheaper?

I was able to read an 04 mk1 tt Jeager MM cluster with Commanderand KKL cable. I had to use Shadow1 for it to pull and it pulled a full 10000 blocks, but listed immo and vin where it was supposed to in the dump.
Tryed that no luck, direct MM reset cluster and after that commander shuts down
Logged
Nothery1952
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 2


« Reply #11 on: February 24, 2019, 03:03:45 AM »

Search for the pattern AUZ* @eeprom mapping location between 0x3800 and 0x3FFF. The two bytes before the search pattern is your pin. For example

@0x3B90 FF FF FF FF FF 02 18 F4 41 55 5A 35 5A 30 42 39 -> ÿÿÿÿÿ.AUZ5Z0B9

0x18F4 coverted to decimal should be 6388. Don´t forget the leading zero that means you have to enter 06388

That´s all! Sorry I´m to lazy to upload a picture.  Wink
« Last Edit: February 24, 2019, 03:06:28 AM by Nothery1952 » Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425



« Reply #12 on: February 24, 2019, 03:24:30 AM »

Vag comander read eeprom only to 0x200 adress  Undecided
Logged
roverguy7
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #13 on: February 25, 2019, 10:03:03 AM »

I would try a few more times with commander. I was able to get one to read, but it did take a few attempts. Try with both Shadow1, and MM Direct. I ran into an error one time when I didn't run commander with administrator privileges.
Logged
b62.7t
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 2


« Reply #14 on: February 27, 2019, 12:54:24 AM »

I just did this, I got a MK1 TT with the MM, I used vag comander and tried all thre options for the MM. MM direct pulled the whole thing then tried what Nothery1952  posted and it worked.
Logged
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.038 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)