|
Title: AUQ to AUM questions Post by: rvukov on April 04, 2021, 06:31:31 AM AUQ to AUM
Hello, I want to increase performance of my stock 1.8t AUM, ECU 06A906032DK V0001, immo3. I prefer to do it with factory maps, and I read about two ways to do it in the forum. First option is to crossflash with AUQ bin, but I don’t know which one is compatible with my ECU, and also am afraid of bricking it. I think that the immo data is in the eeprom, so I don’t have to pair the ECU with cluster after flash? Also, if I get a spare ecu, is it possible to clone my eeprom to it, in case something go wrong? Immo off option is something that I want to avoid. The other option is dump my ecu flash, and replace the maps from auq file, but I’ve never done this before. The map addresses are also different as far as I know. The software and cable that I consider to buy and use is Galletto 1.260 (EOBDII ECU Flasher). This is output from ME7Checker of original 032DK, downloaded from the forum (should be the same as mine): -> Bootrom Version = 05.12 -> EPK = 40/1/ME7.5/5/4013.00//24b/Dst01o/220500// -> Contents of ECUID data table: - '0261206863' (SSECUHN) - '1037354597' (SSECUSN) - '06A906032DK ' (VAG part number) - '0001' (VAG sw number) - '1.8L R4/5VT ' (engine id) -> Contents of ECUID data table: - 'HW_MAN004' -> No errors found. File is OK. ********************* Title: Re: AUQ to AUM questions Post by: stuydub on April 04, 2021, 10:05:27 AM A DK is most likely immo 2 most AUM are immo 3..so if cross flashing u will need to immo off this can be done in the MAP file if u know the address.. DL DR DK HJ HN HS FK and a few more are cross flashable.
Title: Re: AUQ to AUM questions Post by: rvukov on April 04, 2021, 11:09:34 AM A DK is most likely immo 2 most AUM are immo 3..so if cross flashing u will need to immo off this can be done in the MAP file if u know the address.. DL DR DK HJ HN HS FK and a few more are cross flashable. DK (at least that in my car) is 100% immo3. Recently i changed the instrument cluster with VDO (was Jaeger with tons of problems), there was issue with software version of the replacement cluster that i got and a local technician help me to reflash it with different firmware, that supports immo3. That is the 032HN version that i have: Reading Version Strings... -> Bootrom Version = 05.12 -> EPK = 40/1/ME7.5/5/4019.02//24C/Dst02o/220202// -> Contents of ECUID data table: - '0261207440' (SSECUHN) - '1037363908' (SSECUSN) - '06A906032HN ' (VAG part number) - '0002' (VAG sw number) - '1.8L R4/5VT ' (engine id) -> Contents of ECUID data table: - 'HW_MAN004' -> No errors found. File is OK. ********************* Do you think this will work? And if it fails, will i be able to flash back my original file with the Galletto 1.260, or i will need something else? Title: Re: AUQ to AUM questions Post by: Blazius on April 04, 2021, 11:49:30 AM Yes, have bootmode/galletto on hand if you attempt crossflashing.
Title: Re: AUQ to AUM questions Post by: dopefiends on April 21, 2021, 12:44:16 AM Hello ,i am currently trying to do the same.can anybody advice me which is the easiest way and what .bin file shall i look for?off an auq ecu.
My ecu info :6A906032H 0261207436 1032362287 flash:29F800BT Thanks, Sent from my ONEPLUS A5010 using Tapatalk Title: Re: AUQ to AUM questions Post by: stuydub on April 21, 2021, 08:47:25 AM Hello ,i am currently trying to do the same.can anybody advice me which is the easiest way and what .bin file shall i look for?off an auq ecu. My ecu info :6A906032H 0261207436 1032362287 flash:29F800BT Thanks, Sent from my ONEPLUS A5010 using Tapatalk HJ HN HS u can crossflash Title: Re: AUQ to AUM questions Post by: dopefiends on July 12, 2021, 12:44:32 AM HJ HN HS u can crossflash And..what about the immo? Any clue where i could get them maps anyway?Sent from my iPhone using Tapatalk Title: Re: AUQ to AUM questions Post by: stuydub on July 12, 2021, 02:47:23 AM U can edit the map file to immo off if u know the correct address
|