|
Title: Interpolating KFZW? Post by: JeanAwt on July 21, 2024, 09:58:06 PM hi everyone, I didn't understand everything about interpolating the axes on kfzw. I have a maximum of 140 stock and 177 in iop. I understand that the synchronization repeats above 140. should I add a line? replace 140 with 177 or all axes but iop in 11x16 and kfzw in 12x16?? the last 3 axes and make a log? thanks
Title: Re: Interpolating KFZW? Post by: _nameless on July 21, 2024, 10:23:31 PM hi everyone, I didn't understand everything about interpolating the axes on kfzw. I have a maximum of 140 stock and 177 in iop. I understand that the synchronization repeats above 140. should I add a line? replace 140 with 177 or all axes but iop in 11x16 and kfzw in 12x16?? the last 3 axes and make a log? thanks Relinearize the axis values to reflect the load you are running Title: Re: Interpolating KFZW? Post by: JeanAwt on July 22, 2024, 12:56:33 AM Relinearize the axis values to reflect the load you are running my brain is already making bubbles just with this sentence..."Relinearize" so I don't touch the synchronization I just tell it that the load will be 177 instead of 140? nothing else? I read this and it confuses me: "KFZW will use the highest value if the load exceeds the load value defined in the load axis" Title: Re: Interpolating KFZW? Post by: bombis on July 27, 2024, 09:45:08 AM If you run XX deg at 6700rpm and 140 is your max load. timing will still be XX deg at loads above 140.
Adjust axis from 140(old max) to 180(new max), and adjust table to fit the higher loads. Title: Re: Interpolating KFZW? Post by: JeanAwt on July 27, 2024, 10:52:17 PM If you run XX deg at 6700rpm and 140 is your max load. timing will still be XX deg at loads above 140. yes thank you I understood how it worked, but I didn't know if I had to change all the load axes because on my iop they are all higher also there is one more line. I have only modified the last 3 for the moment.Adjust axis from 140(old max) to 180(new max), and adjust table to fit the higher loads. Title: Re: Interpolating KFZW? Post by: bombis on July 29, 2024, 05:12:19 AM yeah probably better to change more of them to make the steps more even
Title: Re: Interpolating KFZW? Post by: _nameless on July 29, 2024, 06:07:26 AM yes thank you I understood how it worked, but I didn't know if I had to change all the load axes because on my iop they are all higher also there is one more line. I have only modified the last 3 for the moment. For example if the last 3 rows are 120, 130, 150 and you have load going up to 170-180 change the last few rows 130, 150, 170 or something like that. Also, you need to change the timing in those rows to reflect the new load scaling too Title: Re: Interpolating KFZW? Post by: JeanAwt on July 29, 2024, 11:42:07 AM For example if the last 3 rows are 120, 130, 150 and you have load going up to 170-180 change the last few rows 130, 150, 170 or something like that. Also, you need to change the timing in those rows to reflect the new load scaling too thank you again, yes it seems logical to modify the timing accordingly. I will check if I have not forgotten other maps where the load will still be in stock limited to 140 |