|
Title: Bench set up and Immo defeat 06A 906 032 HN Post by: onsperformance on November 05, 2013, 08:06:33 AM Hi I have made a bench set-up
http://i1001.photobucket.com/albums/af140/argdub/BenchCable.gif http://i1001.photobucket.com/albums/af140/argdub/bootpin142.jpg I have also Grounded Pin 24 to put the ECU into Boot Mode I am also using the KKL Cable I opened up CMD and typed the following C:\Usesrs\Steven\Downloads\me7_95040.exe Followed by: C:\Usesrs\Steven\Downloads\me7_95040 -r -p 3 95040.bin Com 3 ok boot mode ... failed closing Com 3 No matter what I try I can not get the ECU to fire up in boot mode. Any help would be good! Thanks, Steven Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: oldcarguy85 on November 05, 2013, 09:01:14 AM What procedure are you following to put ECU in boot mode? It sghould be....
1. ecu power off 2. ground pin 24 3. power on ecu. 4. wait 2-3 seconds. 5. remove pin 24 ground 6. try to connect Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: onsperformance on November 23, 2013, 05:18:09 AM Okay I have tried 3 seconds even up to 10 seconds still now joy!
My lupo is all done just run's for a second then cut's out really need to get this done so I can drive it. Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: onsperformance on November 23, 2013, 05:39:16 AM Update:
Com Port:3 Bud Rate: 10400 Opening Com 3 ... OK Initiating communication ... FAIL Closing COM 3 Any Ideas Also I am now doing this over OBD Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: oldcarguy85 on November 23, 2013, 06:01:40 AM What do you mean you are doing it over obd? Do you mean you are doing it in the car?
Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: f1torrents on November 23, 2013, 07:09:43 AM C:\Users\Steven\Downloads\me7_95040 --bootmode 95040 -rp3 95040.bin
This is what your command should look like. You may have to play with the baud rate if its not connecting properly. Edit... I think you are using V1.3? If you are get V1.4... Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: onsperformance on November 24, 2013, 04:34:45 PM C:\Users\Steven\Downloads\me7_95040 --bootmode 95040 -rp3 95040.bin This is what your command should look like. You may have to play with the baud rate if its not connecting properly. Edit... I think you are using V1.3? If you are get V1.4... Yes i am using 1.3 just downloading 1.4 and I have sent you a PM. Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: onsperformance on November 25, 2013, 10:02:30 AM Now i am getting this? using Version 1.4
(http://i743.photobucket.com/albums/xx75/onsperformance/Screenshot2013-11-25165826.png) (http://s743.photobucket.com/user/onsperformance/media/Screenshot2013-11-25165826.png.html) Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: TheDSI on November 25, 2013, 02:52:43 PM you realy need boot mode .
it's a lot faster and stable . Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: onsperformance on November 25, 2013, 04:26:54 PM you realy need boot mode . it's a lot faster and stable . Ok using what Version? Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: ddillenger on November 25, 2013, 04:38:21 PM I run 1.3, find it to be the least buggy.
Title: Re: Bench set up and Immo defeat 06A 906 032 HN Post by: TheDSI on November 26, 2013, 02:46:58 AM used V1.31 yesturday on a 8L0906018K 512k ME7 .
OBD read didn't work . it stop after a minute of reading with an error . bootmode read take about 5s and write about 15s I will test on a 8N0906018J 1M ME7 |