Pages: [1]
Author Topic: 2002 Allroad with Lbox ecu  (Read 5352 times)
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« on: June 21, 2018, 03:45:00 PM »

the car runs on the L box programming, however lots of DTCs for improper coding and what not.
I have both my original 4z7907551m ecu bin and my 95040.bin
how can I put my original ecu bin into the L box and be able to start my car?
will the 95040 need to be reprogrammed via boot mode? ive had no luck with boot mode in the past so that scares me
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Online Online

Posts: 12255


WWW
« Reply #1 on: June 21, 2018, 04:39:05 PM »

Why not code it properly and leave the immo stuff alone?
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« Reply #2 on: June 21, 2018, 04:44:28 PM »

The s4 ecu won't take allroad soft coding I tried. Perhaps I'm doing it wrong?

Sent from my Z917VL using Tapatalk

Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Online Online

Posts: 12255


WWW
« Reply #3 on: June 21, 2018, 05:23:39 PM »

The s4 ecu won't take allroad soft coding I tried. Perhaps I'm doing it wrong?

Ah its an s4 8D0 L box, not a 4z7?

Yes, you'll need to flash it with 4z7m and your eeprom

Yes, you'll have to use bootmode.

What should scare you is doing any flashing without a working bootmode setup.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« Reply #4 on: June 22, 2018, 09:13:18 AM »

until recently i've had good luck (I flashed an ecu without first verifying checksums, my own mistake)
well shit. I have a bench flash setup, ive just never been able to get boot mode to work
id LOVE to get these lights turned off but it sounds like im gonna need some help doing so, unless I can mail my original
4z7907551m to someone to have them recover it....
Logged
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« Reply #5 on: June 24, 2018, 02:01:20 PM »

Upon further inspection it has to be my bench harness.  I plugged a known working ecu into it and vcds won't even connect.  Time to break out a multimeter

Sent from my Z917VL using Tapatalk

Logged
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« Reply #6 on: June 25, 2018, 02:49:19 PM »

and all of the 12v pins have 12v (11.3 actually, perhaps the problem?) and the grounds are grounds.
k line has continuity to the obd port of my bench harness. im stumped
Logged
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« Reply #7 on: August 09, 2018, 10:43:34 AM »

anyone in the PNW that can help me out? id love to get all these lights turned off and my ride height control working properly.
also still have my old 4z7 ecu I could use if someone would be willing to UNbrick it for me. my dumb ass flashed an incorrectly checksumed file and killed it.
Logged
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« Reply #8 on: August 23, 2018, 09:50:18 AM »

still looking for help guys. anyone that can point me in the right direction.
Logged
m_haiser
Full Member
***

Karma: +0/-2
Offline Offline

Posts: 68


« Reply #9 on: December 13, 2018, 01:33:58 PM »

I'd still love to get this taken care of. ori ecu is either fried or I cannot get it or any other ecu ive tried into bootmode.
would really like some help here guys
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0s, 0q)