Pages: 1 2 [3]
Author Topic: 4F0 907 559 Few parameters help needed  (Read 19501 times)
prj
Hero Member
*****

Karma: +1072/-480
Offline Offline

Posts: 6035


« Reply #30 on: June 20, 2020, 03:33:39 AM »

The gearbox should have the file that is originally for it. Don't try to crossflash, because there can be hardware differences.
Gearbox can be tuned to do whatever.
Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
Stoti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 79


« Reply #31 on: July 11, 2020, 03:46:18 PM »

I have tested it it was from 3.2 FSI simos ecu . Cross flashed it to 4.2 BAT engine and it was running ever better with dual ecu setup but it was cutting the throttle  and no TC lock because of missing 99% of sensors . Flashed after that to BBJ 3.0 MPI because i was using this ecu that started the topic and maybe i still will be drive it  with this ecu if Marty did not tell me what do try . I dont have time to finsh the project and see what will happend when she see boost . I have to try to put original flash for grarbox to see is the sjmos ussing same can  commands.
Logged
Stoti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 79


« Reply #32 on: August 10, 2020, 02:49:24 AM »

CWGGVFZG Set to 2  VSS working . Thank you prj . I have 150 km drive no issues for now . I have to disable some dtc for brake boost pump and airbag crash signal. Because i have only this left . One big red brake sign on dasgboard . But i can live with it Smiley  Thank you again guys .
Logged
Stoti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 79


« Reply #33 on: September 01, 2020, 09:43:39 AM »

update :

ABS softcoding 0005025 for bosch esp8 4F0910517L works without any additional software manipulating .


Close fuel tank cap , and oil level max signs appear only if somebody know where to post new topic Smiley
Logged
Legendshark
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #34 on: January 20, 2021, 07:10:28 AM »

Hey,
I got an 2.7T Swap too. Are u still in the game? Did u fixed problems with the Speedsignal on Can? The Tank Clap problem is in mine too. And how do your car start? I got a button but then the rest of this C6 stands in ignition on not in KL.50 starting. Did u implementing the BBJ ECU. I Got 4Z7907551N BES ECU. My Car is a manual one. MAybe you could help me a bit.
Logged
dus
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18


« Reply #35 on: January 21, 2021, 02:12:52 AM »

Did u fixed problems with the Speedsignal on Can?

CWGGVFZG Set to 2  VSS working

and check pm
Logged
Stoti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 79


« Reply #36 on: November 16, 2021, 06:10:06 PM »

Hey,
I got an 2.7T Swap too. Are u still in the game? Did u fixed problems with the Speedsignal on Can? The Tank Clap problem is in mine too. And how do your car start? I got a button but then the rest of this C6 stands in ignition on not in KL.50 starting. Did u implementing the BBJ ECU. I Got 4Z7907551N BES ECU. My Car is a manual one. MAybe you could help me a bit.

There is arduaudi controler guys are developing for b7 platform with 2.7 swap they implement start signal via CAN , ac contrroll , fan control and cruise control look for it (i build my own with lcd) . For starter i hooked to ign lock to get 5v signal and enable relay im keeping it simple but i have heared that is possible me7.1.1 to output signal and cut when engine start ,but i dont need this . Update on post Car is now on Hybrid turbos and its driving good 15K+ KM. Still auto, little annoying , laggy and cuts boost till 3k but on S is perfect Smiley 
Logged
dus
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18


« Reply #37 on: May 23, 2022, 03:13:33 AM »

CANVERS, FMOTC, CWGC

these parameters are displayed in measurement group number 12 of the transmission control unit
Logged
Pages: 1 2 [3]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.035 seconds with 17 queries. (Pretty URLs adds 0.005s, 0q)