Readiness table not found

Pages: 1 [2]

« previous next »

Author

Topic: Readiness table not found (Read 13841 times)

ddillenger

Hero Member

Karma: +641/-21
Offline

Offline

Posts: 5640

	Re: Readiness table not found « Reply #15 on: November 20, 2013, 11:41:56 AM »

The only time you would need ESKONF is if you unplug the SAI relay.


	Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM

technic

Full Member

Karma: +18/-5
Offline

Offline

Posts: 227

	Re: Re: Readiness table not found « Reply #16 on: November 20, 2013, 11:49:31 AM »

Exactly. And didn't change ESKONF, so I used a resistor to trick it. Not that it really matters on the bench Wink


	Logged

technic

Full Member

Karma: +18/-5
Offline

Offline

Posts: 227

	Re: Readiness table not found « Reply #17 on: November 20, 2013, 01:57:06 PM »

Thanks for helping me out, both of you


	Logged

technic

Full Member

Karma: +18/-5
Offline

Offline

Posts: 227

	Re: Readiness table not found « Reply #18 on: March 09, 2014, 02:57:26 AM »

I'm trying to take this a step further and remove some more SAI related hardware.

I have been looking for AA FF 00 30 33 F8 30 (or parts there of). It's easily located in my me7 damos right before KFKHFM, but again I cannot find it in the 8N0906018AE. Since these are bit switches, I have looked for "variants" also. AA FF I have assumed is valid - four ignition coils and 4 NC.

ddillenger will probably yell at me because I didn't look hard enough Cool

but please, give me a hint at least.


	Logged

ddillenger

Hero Member

Karma: +641/-21
Offline

Offline

Posts: 5640

	Re: Readiness table not found « Reply #19 on: March 09, 2014, 08:50:54 AM »

Hint:

Narrowband starts with FF FF 00


	Logged

technic

Full Member

Karma: +18/-5
Offline

Offline

Posts: 227

	Re: Readiness table not found « Reply #20 on: March 09, 2014, 08:58:54 AM »

Now we are talking. Thanks Wink


	Logged

technic

Full Member

Karma: +18/-5
Offline

Offline

Posts: 227

	Re: Readiness table not found « Reply #21 on: March 22, 2014, 03:26:02 AM »

Quote from: ddillenger on November 19, 2013, 03:20:49 PM

MSLUB=Passed, but only after the requisite amount of time. The tests with VCDS will just abort.

What timeframe and prerequisites are we talking about here? I did test with _only_ MSLUB=0 and got OBDII Readiness Passed (And VCDS Passed) when first checking after a week or so.
Then I was doing some other test that had nothing to do with SAI. During those tests SAI was enabled (MSLUB = stock)

When I put the software with MSLUB=0 back, it don't show readiness passed, even after a one hour drive. Huh

Edit : Drive one hour today, and 15 minutes yesterday.


« Last Edit: March 23, 2014, 11:21:27 AM by technic »	Logged

technic

Full Member

Karma: +18/-5
Offline

Offline

Posts: 227

	Re: Re: Readiness table not found « Reply #22 on: March 25, 2014, 02:41:54 PM »

Now readiness is set again. I guess I didn't allow it to idle when cold long enough.


	Logged

ddillenger

Hero Member

Karma: +641/-21
Offline

Offline

Posts: 5640

	Re: Readiness table not found « Reply #23 on: March 25, 2014, 03:03:14 PM »

You can set it manually as well, but the test might abort a few times before it passes.

Otherwise, a few cold start cycles where the SAI pump would be expected to run is all it takes.


	Logged

Pages: 1 [2]

« previous next »

Jump to:

Navigation

Personal Tools

November 17, 2024, 06:34:46 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search