NefMoto > Technical > Reverse Engineering > ME7.5 and C167
Pages: [1]
« previous next »
Author Topic: ME7.5 and C167  (Read 14252 times)
Ionut
Full Member
***

Karma: +4/-3
Offline Offline

Posts: 89
« on: December 19, 2013, 03:55:14 AM »
Hello.
I`m new in dissasembly ecu (yesterday first day Tongue ).
I Work with IDA Pro and 032AF file.
I know C167 has internal ROM and flash and is connected to 29F400BB / 29F800BB.

Firstly, i`m curious the IMMO check routine is stored in external flash or in internal processor`s flash?
Secondly, On C167 datasheet i`ve didn`t found the way processor boots-up. Wich routine is called. If Reset is performed first, wich routine is next?
And how maps are called from software?
For example i have the KFMIRL map starting at 0x123DC but didn`t found that part in dissasembled flash image.

Could you please help me understand where map selection routine begins and how is made?

Thank you in advance.
Logged
Aurélien
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 60
« Reply #1 on: December 22, 2013, 07:10:02 AM »
Where is your CPU read ?
Logged
Ionut
Full Member
***

Karma: +4/-3
Offline Offline

Posts: 89
« Reply #2 on: December 22, 2013, 10:02:35 AM »
as i know, there are 2 types of dump.

For example, how to find map address and entry point from attached dump?
Logged
Aurélien
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 60
« Reply #3 on: December 22, 2013, 12:29:25 PM »
I don't think you can use C167 from RS4/S4 to disassemble 1.8T file.

I'm not sure about the memory mapping for 29F400 file but I would do the following :

A_ Load your IROM C167 binary first to defaut value
B_ Create your IRAM segment 0xE000 length 0x10000
C_ Load your ROM 06A906032AF file at 0x800000 length defaut value ( file size )
D_ Create your RAM segment at 0x380000 length 0x20000

The code and data follow that structure :

CODE1 0x800000 - 0x80FFFF , length 0x0000FFFF
DATA1 0x810000 - 0x81FFFF , length 0x0000FFFF
CODE2 0x820000 - 0x87FFFF , length 0x0005FFFF

At first, select whole code1 and press C, ignore error. Same for code 2.

Then go to map adress ( don't forget there is a 0x800000 offset compared to winols ), give the right shape ( create array ) and follow xref.
Good luck.
Logged
Ionut
Full Member
***

Karma: +4/-3
Offline Offline

Posts: 89
« Reply #4 on: December 22, 2013, 01:55:19 PM »
ok, so let me understand. I need to load default IROM (32K) inside Ida Pro. After this i need to load the 512K (my dump from ECU)?
But how ca i find the boot sequenc and where maps are loaded?
I want this mainly because i want to know how is selected KLBTS and where is located TABGBTS in my file.
Logged
Aurélien
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 60
« Reply #5 on: December 23, 2013, 03:14:05 AM »
Yes.

You maps will be in the data area :

DATA1 0x810000 - 0x81FFFF , length 0x0000FFFF

Go in winols and look for KFLBTS, go to that adress ( + offset 0x800000 ) in IDA and follow XREF, there should only have 1 subroutine.

This subroutine will tell you how it works after you analyse it. You will also find map axis and other LBTS related maps.
Logged
Ionut
Full Member
***

Karma: +4/-3
Offline Offline

Posts: 89
« Reply #6 on: December 23, 2013, 03:50:28 AM »
do my kfmirl address that i should search for is 0x800000 + 0x123dc ?
that means 0x8123dc ?
Logged
Aurélien
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 60
« Reply #7 on: December 23, 2013, 11:30:09 AM »
Yes, KFMIRL Z data will be at 0x8123DC in that case.  Wink
Logged
Ionut
Full Member
***

Karma: +4/-3
Offline Offline

Posts: 89
« Reply #8 on: December 23, 2013, 02:43:17 PM »
searched all refs to 0x123dc, 0x123dc and nothing found. Did i miss something?
Logged
Aurélien
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 60
« Reply #9 on: December 23, 2013, 04:29:49 PM »
Yes. How map is referenced.

Look for KFLDRL, it's easier. If you find a reference to that map, you are doing it right.
Logged
Ionut
Full Member
***

Karma: +4/-3
Offline Offline

Posts: 89
« Reply #10 on: December 24, 2013, 02:14:49 AM »
i can`t find anything related to 812C94h wich is address of KFLDRL.
Logged
dream3R
Hero Member
*****

Karma: +18/-8
Offline Offline

Posts: 1194
« Reply #11 on: December 24, 2013, 04:56:24 AM »
It will be offset my DPP so try masking more off
Logged


How to work out values from an A2L Smiley

http://nefariousmotorsports.com/forum/index.php?topic=5525.msg52371#msg52371


Starting Rev's http://nefariousmotorsports.com/forum/index.php?topic=5397.msg51169#msg51169

noobs read this before asking http://nefariousmotorsports.com/forum/index.php?topic=9014.0title=


ORGORIGINAL 05 5120 creator for Volvo
ORIGINAL Datalogger (Freeware) Author
ORGINAL finder of the 'extra' torque' limits
I don't have ME7.01 A2L I just use ID
Ionut
Full Member
***

Karma: +4/-3
Offline Offline

Posts: 89
« Reply #12 on: January 04, 2014, 04:27:18 PM »
How can i read my C167 dump? i have a Galleto and VCDS and bench setup for it.
I`ve made the 10x16 array of KFLDR and looks like on WinOLS, but how do i find xrefs? http://screencast.com/t/ZAwDhocKgsR
« Last Edit: January 04, 2014, 05:49:31 PM by Ionut » Logged
geo22
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5
« Reply #13 on: August 06, 2019, 11:17:47 PM »
Bump!

Not to create new topic can I ask here?
Now Im trying to dig into c167 disassembly. How can I find where is addressing to a particular map? Found a map address in the a2l but there is no direct link from code section to this map. So I guess its some kind of indirect addressing. Could someone give me a tip where to search?

 
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 28, 2024, 05:36:12 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.021 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)