NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > ME 3.8.3 fgtech galletto 4
Pages: [1]
« previous next »
Author Topic: ME 3.8.3 fgtech galletto 4  (Read 4733 times)
fgtskofd
Full Member
***

Karma: +0/-13
Offline Offline

Posts: 91
« on: December 21, 2015, 11:08:33 AM »
hello

im looking at turning the IMMO off on a me3.8.3 iv only got tools kwp2000 and fgtech galletto 4.

been doing lots of research and haven't found anything concrete for setting up this ecu in boot mode.
i may have overlooked something on this topic, any help or guidance would be greatly appreciated. i have not worked
with this ecu before

thanks 
Logged
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655
« Reply #1 on: December 21, 2015, 11:12:55 AM »
you havent found anything about bootmode because there is no bootmode for them.
Logged
fgtskofd
Full Member
***

Karma: +0/-13
Offline Offline

Posts: 91
« Reply #2 on: December 21, 2015, 11:25:33 AM »
ah i see thanks for the reply do i need to buy a EEPROM USB Programmer then ?

Logged
fgtskofd
Full Member
***

Karma: +0/-13
Offline Offline

Posts: 91
« Reply #3 on: December 21, 2015, 12:06:40 PM »
or should i remove chip 24c04 and get a reader for it ?

thanks
Logged
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655
« Reply #4 on: December 21, 2015, 04:28:44 PM »
desolder and use programmer.
Logged
fgtskofd
Full Member
***

Karma: +0/-13
Offline Offline

Posts: 91
« Reply #5 on: December 21, 2015, 08:20:03 PM »
thanks found a topic for this finally


http://nefariousmotorsports.com/forum/index.php?topic=5622.0
Logged
oxide32
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21
« Reply #6 on: December 22, 2015, 11:29:59 AM »
Quote from: grizzle245 on December 21, 2015, 12:06:40 PM
or should i remove chip 24c04 and get a reader for it ?

thanks
I have also tried using a test clip with this chip but it's very hit and miss if it will work. Just grab a hot air solder station. They aren't expensive and mines paid for itself time and again
Logged
h100vw
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 34
« Reply #7 on: December 22, 2015, 07:01:38 PM »
I get them off with a gas soldering iron and the hot air nozzle. A little lifting pressure off a scalpel blade and you can hear when the legs start to let go off the board.

Mark the board and chip obviously.  Wink
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 23, 2024, 10:57:04 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)