NefMoto > Technical > Tuning > Changing KFNWSE map axis
Pages: [1]
« previous next »
Author Topic: Changing KFNWSE map axis  (Read 7208 times)
giles92
Full Member
***

Karma: +13/-3
Offline Offline

Posts: 83
« on: June 04, 2016, 02:02:22 PM »
I want to extend the KFNWSE map rpm axis further than 4000 rpm. Is that axis shared with other timing maps? anyone else done it?
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #1 on: June 06, 2016, 03:52:18 AM »
Quote from: giles92 on June 04, 2016, 02:02:22 PM
I want to extend the KFNWSE map rpm axis further than 4000 rpm. Is that axis shared with other timing maps? anyone else done it?

what makes you think it stops at 4000?most if not all the ones I've seen go to 6250 anyway..

Post the original file
Logged
giles92
Full Member
***

Karma: +13/-3
Offline Offline

Posts: 83
« Reply #2 on: June 06, 2016, 02:57:37 PM »


Ive attached a stock file as well. Thanks
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #3 on: June 07, 2016, 03:57:36 AM »
Quote from: giles92 on June 06, 2016, 02:57:37 PM


Ive attached a stock file as well. Thanks

Hi, yep you are correct the axis on the xdf I've seen goes to 4000, now it could be a mistake and have the wrong axis listed I dont know.. Only real way to check is to dissamble the file and see where the axis is pointing to get the address, it's assuming on this xdf its correct which it may not be, I don't know
Logged
nubcake
Sr. Member
****

Karma: +53/-4
Offline Offline

Posts: 400
« Reply #4 on: June 07, 2016, 04:49:14 AM »
Post your bin.
Logged
giles92
Full Member
***

Karma: +13/-3
Offline Offline

Posts: 83
« Reply #5 on: June 07, 2016, 06:50:40 PM »
the bin im using is in my prev post under the image.
Logged
nubcake
Sr. Member
****

Karma: +53/-4
Offline Offline

Posts: 400
« Reply #6 on: June 08, 2016, 03:54:31 AM »
Quote from: giles92 on June 07, 2016, 06:50:40 PM
the bin im using is in my prev post under the image.

Right. My bad.

The axis is SNM16NEUW, located at 0x13208.
Used also by: KFNWWLE (0x2A836), KFNWKRE (0x2A604) and KFNWKHE (0x2A4D2).
Logged
giles92
Full Member
***

Karma: +13/-3
Offline Offline

Posts: 83
« Reply #7 on: June 08, 2016, 10:36:40 AM »
Wow thats awesome. Could you give me a shorthand idea of how you did that? Disassembly in IDA? I need to get on that level. Stage1+2 dont require many axis changes but now stage 3 i find mysef wanting to adjust load axis and rev axis all over. I know some axis will top out because of size/resolution. Thanks for the info.
Logged
nubcake
Sr. Member
****

Karma: +53/-4
Offline Offline

Posts: 400
« Reply #8 on: June 08, 2016, 12:21:46 PM »
Quote from: giles92 on June 08, 2016, 10:36:40 AM
Wow thats awesome. Could you give me a shorthand idea of how you did that? Disassembly in IDA? I need to get on that level. Stage1+2 dont require many axis changes but now stage 3 i find mysef wanting to adjust load axis and rev axis all over. I know some axis will top out because of size/resolution. Thanks for the info.

Disassembly, yes. Check the thread I made on making a (still untested, lol) 5120 for the RS6. Specifically, this post has a compilation of needed stuff for your binary.
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #9 on: June 08, 2016, 10:23:56 PM »
Quote from: giles92 on June 08, 2016, 10:36:40 AM
Wow thats awesome. Could you give me a shorthand idea of how you did that? Disassembly in IDA? I need to get on that level. Stage1+2 dont require many axis changes but now stage 3 i find mysef wanting to adjust load axis and rev axis all over. I know some axis will top out because of size/resolution. Thanks for the info.

Do you know how to adjust the axis?
Logged
giles92
Full Member
***

Karma: +13/-3
Offline Offline

Posts: 83
« Reply #10 on: June 09, 2016, 06:56:25 AM »
Yeah ive done it with lamfa and ldrxn. So if all of them share that axis in theory i could adjust the axis and then adjust those other three maps so that they were compensated with the axis shift and still had the same functional output?
Logged
nubcake
Sr. Member
****

Karma: +53/-4
Offline Offline

Posts: 400
« Reply #11 on: June 09, 2016, 09:16:39 AM »
Quote from: giles92 on June 09, 2016, 06:56:25 AM
if all of them share that axis in theory i could adjust the axis and then adjust those other three maps so that they were compensated with the axis shift and still had the same functional output?

Yes.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 28, 2024, 11:30:39 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.034 seconds with 18 queries. (Pretty URLs adds 0s, 0q)