Boot mode help -

Pages: [1] 2

« previous next »

Author

Topic: Boot mode help - (Read 14917 times)

andrew8527

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Boot mode help - « on: June 19, 2016, 06:52:08 PM »

Have an ME7.5, MTM chipped 518F box that I'm trying to IMMO defeat:

I have been unsuccessful in getting into boot mode though and would appreciate any troubleshooting tips.

I have a purple eBay cable configured as such:

Bench voltage is 13.5. I've tried grounding the boot pin (24) for various lengths of time from 2 to 10 seconds but I keep getting an immediate 'check cable' error - very quickly. I believe the cable to be good though, as I can connect via OBD with VAG Can commander. In addition, it is recognized by the Nefmoto flashing tool and connects via OBD with the Nefmoto tool.

No communication over OBD either, though it at least pauses for about 2-3 seconds before giving me the FAIL:

Hopefully, I'm making a simple mistake somewhere......

Thanks in advance.


	Logged

aef

Hero Member

Karma: +70/-46
Offline

Offline

Posts: 1601

	Re: Boot mode help - « Reply #1 on: June 20, 2016, 06:06:33 AM »

try it with baud rate of 57600
Can you see the underside of the mtm board?


	Logged

andrew8527

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Re: Boot mode help - « Reply #2 on: June 20, 2016, 10:00:08 AM »

thanks, I have tried all possible baud rates.

anything in particular you're looking for on the underside of the mtm chip?

Quote from: aef on June 20, 2016, 06:06:33 AM

try it with baud rate of 57600
Can you see the underside of the mtm board?


	Logged

nyet

Administrator
Hero Member

Karma: +608/-168
Offline

Offline

Posts: 12271

	Re: Boot mode help - « Reply #3 on: June 20, 2016, 10:26:13 AM »

remove the riser, put it in boot mode, flash the eeprom, replace the riser.


	Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex

andrew8527

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Re: Boot mode help - « Reply #4 on: June 20, 2016, 10:59:55 AM »

special tools required or just a steady hand and patience?

same nyet as over on Audiworld? Wink

thanks.


	Logged

Carsinc

Sr. Member

Karma: +17/-2
Offline

Offline

Posts: 447

	Re: Boot mode help - « Reply #5 on: June 20, 2016, 05:59:53 PM »

It might slip right off. I'm not sure soldering is needed


	Logged

nyet

Administrator
Hero Member

Karma: +608/-168
Offline

Offline

Posts: 12271

	Re: Boot mode help - « Reply #6 on: June 20, 2016, 08:18:37 PM »

It's clearly a simple socket. Pull gently and evenly.


	Logged

andrew8527

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	IMMO off please « Reply #7 on: July 13, 2016, 09:37:37 AM »

Turns out the bench harness I was borrowing from a reputable forum member had a fault in it. After reconfiguring it, I was able to download the 95040 on the first try.

Now, could someone assist with IMMO OFF please? Grin


	Logged

Carsinc

Sr. Member

Karma: +17/-2
Offline

Offline

Posts: 447

	Re: Boot mode help - « Reply #8 on: July 13, 2016, 11:50:31 AM »

I'm sure someone will help, but could you please just try,
http://nefariousmotorsports.com/forum/index.php?topic=2973.0title=


	Logged

dozer103

Jr. Member

Karma: +1/-0
Offline

Offline

Posts: 26

	Re: Boot mode help - « Reply #9 on: July 13, 2016, 11:54:08 AM »

^ x2. Daz's immooff bin worked like a charm on my 518F.


	Logged

andrew8527

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Re: Boot mode help - « Reply #10 on: July 19, 2016, 07:23:14 PM »

thanks for the tips so far, was able to verify checksums on my immo defeated .bin. Now, I'm back to needing any boot mode tips!

C:\Users\Ranford>C:\Users\Ranford\Desktop\ME7gui106\ME7gui\ME7EEPROM.exe --boot
ode 95040 -wp1 "C:\users\Ranford\desktop\immoff.bin"
ME7_EEPROM v1.40
COM: 1, Baud Rate: 10400
Memory type: 95040, size: 512
Opening COM1 ... OK
Starting Boot_mode ... uC ID response 0xC5: C167CR ... OK
Sending Loader + MonitorCore ... MonitorCore successfully launched
Initializing registers ... OK
Sending EEPROM driver ... OK
Searching Chip_Select pin ... P4.7
Configuring SPI Interface ... OK
Checking EEPROM Status Register ... 0x00F0
Writing EEPROM ................................ OK
Verifying EEPROM write ... FAIL. (error=0x70101)
Closing COM1

So close, it seems! I've already tried all possible baud rates. I found an old post basically saying - "keep trying, ME7.x is stubborn."
Any other "variables" you'd recommend changing.....file name? location of the program? Thanks.


	Logged

_nameless

Hero Member

Karma: +342/-466
Offline

Offline

Posts: 2802

	Re: Boot mode help - « Reply #11 on: July 19, 2016, 11:08:18 PM »

TRY IT IM SURE IT WILL WORK. IT ALWAYS REPORTS THAT ERROR WHEN I USED IT BUT ALWAYS WORKED FINE


	Logged

Giving your mom a tuneup

nyet

Administrator
Hero Member

Karma: +608/-168
Offline

Offline

Posts: 12271

	Re: Boot mode help - « Reply #12 on: July 19, 2016, 11:29:53 PM »

Quote from: Marty on July 19, 2016, 11:08:18 PM

TRY IT IM SURE IT WILL WORK. IT ALWAYS REPORTS THAT ERROR WHEN I USED IT BUT ALWAYS WORKED FINE

WHAT PLEASE SPEAK UP


	Logged

Carsinc

Sr. Member

Karma: +17/-2
Offline

Offline

Posts: 447

	Re: Boot mode help - « Reply #13 on: July 20, 2016, 11:32:32 AM »

YEA IT ALWAYS DOES THAT!

Why are we yelling now?


	Logged

k0mpresd

Hero Member

Karma: +146/-54
Offline

Offline

Posts: 1655

	Re: Boot mode help - « Reply #14 on: July 20, 2016, 11:41:08 AM »

mine never does not verify correctly. using kkl and rosstech hexcan cables.


	Logged

Pages: [1] 2

« previous next »

Jump to:

Navigation

Personal Tools

November 30, 2024, 09:36:14 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?