up50lut3
Full Member
Karma: +1/-0
 Offline
Posts: 55
|
 |
« on: October 15, 2016, 04:38:44 PM »
|
|
|
hey all,
i have a CEL that keeps poping for ABS and Airbag modules not present. i have disabled all options per my can-bus gateway, but this is in my engine ecu, not the canbus.
does anyone know what address and what to change them to iin order to disable either the ecu looking for the modules, or disable the ecu from reporting an error?
car does not have abs nor airbags...its a 1.8t swap into a mk3... full me7.5 harness tho.
Thanks in advaced?
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #1 on: October 15, 2016, 10:03:07 PM »
|
|
|
Post your binary..
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
|
nubcake
|
|
« Reply #2 on: October 16, 2016, 02:07:13 AM »
|
|
|
CW_CAN_R and/or CW_CAN_C most likely.
|
|
|
|
|
Logged
|
|
|
|
up50lut3
Full Member
Karma: +1/-0
Offline
Posts: 55
|
|
« Reply #3 on: October 16, 2016, 08:03:19 AM »
|
|
|
does it need to have the codes in it, on? i.e. do you need a version that i've run and popped codes for of is the one, not flashed ok?
|
|
|
|
|
Logged
|
|
|
|
up50lut3
Full Member
Karma: +1/-0
Offline
Posts: 55
|
|
« Reply #4 on: October 16, 2016, 08:08:15 AM »
|
|
|
does it need to have the codes in it, on? i.e. do you need a version that i've run and popped codes for of is the one, not flashed ok?
here it is, as it sits...before writing to car and throwing codes. editied file removed |
|
|
|
« Last Edit: October 19, 2016, 11:33:39 AM by up50lut3 »
|
Logged
|
|
|
|
up50lut3
Full Member
Karma: +1/-0
Offline
Posts: 55
|
|
« Reply #5 on: October 16, 2016, 08:11:38 AM »
|
|
|
sorry, i have no idea how to edit posts  ( i know) its 06A 032 906 HS if it matters |
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #6 on: October 16, 2016, 08:26:45 AM »
|
|
|
here it is, as it sits...before writing to car and throwing codes.
The flash is the same before and after writing to the car and throwing codes. It never changes on it's own. I have the locations for this, I'll take a look in a bit. |
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
|
vwaudiguy
|
|
« Reply #7 on: October 17, 2016, 10:03:24 AM »
|
|
|
Set these two location to 00 in your file.
0x107A7
0x10802
Don't forget to checksum before flashing.
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
up50lut3
Full Member
Karma: +1/-0
Offline
Posts: 55
|
|
« Reply #8 on: October 17, 2016, 11:14:43 AM »
|
|
|
Set these two location to 00 in your file.
0x107A7
0x10802
Don't forget to checksum before flashing.
Thank you! |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #9 on: October 17, 2016, 11:16:01 AM »
|
|
|
I would add, please do not zero out anything on someone's advice until you understand WHY you are doing it ... please at least take a peek at the FR before blinding changing things  Thank you. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #10 on: October 17, 2016, 11:16:37 AM »
|
|
|
sorry, i have no idea how to edit posts ( i know) its 06A 032 906 HS if it matters "modify" |
|
|
|
|
Logged
|
|
|
|
up50lut3
Full Member
Karma: +1/-0
Offline
Posts: 55
|
|
« Reply #11 on: October 18, 2016, 12:40:16 AM »
|
|
|
Thanks....i do. It's a swap into a mk3...no airbags and no abs.....check engine light off only of system disabled...it's ok Sent from my iPad using Tapatalk |
|
|
|
|
Logged
|
|
|
|
up50lut3
Full Member
Karma: +1/-0
Offline
Posts: 55
|
|
« Reply #12 on: October 19, 2016, 11:32:51 AM »
|
|
|
hey all,
i recently made a post asking someone to help me code out my abs and airbags.. now i need to delete a dtc, not the system, just the dtc( its a swap and still want the system activated as i only need the cel off for inspection( yes just the light off, readyness doesn't matter).
I read the sticky above, but i don't think it corrisponds to my ecu files.( 06A 906 032 SM )
SO is there anyone someone can explain( as direct as possible) how to find the dtc, turn it off( i image change to "00"?) and if i wanted to find the system it correspond to if i did want to try to disable the system?
or atleast just how to find the dtc and turn it off? i have the maps for it, but still dont understand how to loacate these thing)
Im trying to lern, but im a lern by example kind of guy, sorry..
thanks in advaced, if you can take a few to explain it! thanks
Here is my file, and the maps im using
|
|
|
|
|
Logged
|
|
|
|
|
|
up50lut3
Full Member
Karma: +1/-0
Offline
Posts: 55
|
|
« Reply #14 on: October 19, 2016, 08:35:03 PM »
|
|
|
Sorry, it's an hs file... I was think of what my other car when I wrote that...
Sent from my iPad using Tapatalk
|
|
|
|
|
Logged
|
|
|
|
|
