dokalanyi
Full Member
Karma: +4/-1
 Offline
Posts: 118
|
 |
« on: November 21, 2016, 05:46:24 AM »
|
|
|
Been following the 1.8T community tune, however, correction factors don't make me feel safe continuing.
I'm getting knock when I've barely increased LDRXN -- Actually, I had to increase LDRXNZK, it's not following LDRXN.
- I've tried using the best fuel I could find (Shell V-Power), for a week, to clear out any "old" fuel. And also cleared errors to reset trims
- My suspicion is maybe intake air temperatures are high?
- I tried waaay running rich at one point
I've attached the latest log I did. Ambient was around 19C/66.2F
EDIT:
I also have these 2 error messages, almost always. I never disconnect my battery, and I've replaced the vehicle speed sensor on the gearbox. No ABS errors
18010 - Power Supply Terminal 30
P1602 - 35-10 - Voltage too Low - Intermittent
16885 - Vehicle Speed Sensor
P0501 - 35-00 - Implausible Signal
|
|
|
|
« Last Edit: November 21, 2016, 05:53:12 AM by dokalanyi »
|
Logged
|
|
|
|
|
aef
|
|
« Reply #1 on: November 21, 2016, 06:08:27 AM »
|
|
|
iat is shit, that is for sure -> BTS is kicking in
|
|
|
|
|
Logged
|
|
|
|
|
SB_GLI
|
|
« Reply #2 on: November 21, 2016, 06:13:54 AM »
|
|
|
IAT aren't great, but timing curve needs some work. Too advanced by 4,000rpm.
|
|
|
|
|
Logged
|
|
|
|
dokalanyi
Full Member
Karma: +4/-1
Offline
Posts: 118
|
|
« Reply #3 on: November 21, 2016, 06:16:50 AM »
|
|
|
iat is shit, that is for sure -> BTS is kicking in
I doubt BTS is kicking in -- thought it was LAMFAWKR. TABGBTS is set to 1050C IAT aren't great, but timing curve needs some work. Too advanced by 4,000rpm.
It's stock timing, that's why I thought I shouldn't touch it |
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #4 on: November 21, 2016, 06:23:07 AM »
|
|
|
BTS for me is Bauteilschutz, which is Parts Self Protection or something in english.
Your IAT is too hot, thats all i tell you.
|
|
|
|
|
Logged
|
|
|
|
dokalanyi
Full Member
Karma: +4/-1
Offline
Posts: 118
|
|
« Reply #5 on: November 21, 2016, 12:18:21 PM »
|
|
|
How do I drop IATs? I'm in a tropical country, temperatures are 22-30C all year, almost all the time.
FMIC:
- Expensive to ship -- more than the cost of buying the front mount intercooler itself
- Waters/Meth: easier to ship, just worried about water consumption.
What's your take as a hack for this?
|
|
|
|
|
Logged
|
|
|
|
dokalanyi
Full Member
Karma: +4/-1
Offline
Posts: 118
|
|
« Reply #6 on: November 21, 2016, 09:42:00 PM »
|
|
|
Passat B5.5. I can only pick one  |
|
|
|
|
Logged
|
|
|
|
dokalanyi
Full Member
Karma: +4/-1
Offline
Posts: 118
|
|
« Reply #7 on: November 22, 2016, 01:52:26 AM »
|
|
|
Are you running spec coolant? if you or a previous owner didnt run proper g12, g12+ or g12++ coolant then you likely have excessive buildup, rust and or/deterioration somewhere within your coolant loop. and if this is the case your pump could have gotten clogged therefore your cooling system can no longer dissipate the heat produced by your engine.
I'm definitely not running spec coolant. But the coolant temperature is actually always around 90C (even in the log, not just the cluster). I'll try to flash the system with spec coolant to get that outta the way First things first can you hear your radiator fans functioning at all? you should have 2. a large one and a secondary. In your tune you can change the threshold temp your fans will kick on at. Check that and make sure you dont have it set too high. Lower it and make it come on at a lower temp.
The fans work. The second one mainly comes when I turn on the AC, and when I start the car, then goes off. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #8 on: November 22, 2016, 02:03:06 AM »
|
|
|
His coolant temps are fine, and his cooling system isn't going to change IATs Stop making shit up  |
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #9 on: November 22, 2016, 02:36:17 AM »
|
|
|
Coolant temp didn't budge from 90 (+-1 deg). That won't change AITs.
Don't trim logs either.
|
|
|
|
|
Logged
|
|
|
|
|
IamwhoIam
|
|
« Reply #10 on: November 22, 2016, 03:19:40 AM »
|
|
|
jeeeeeeeeeeez
|
|
|
|
|
Logged
|
I have no logs because I have a boost gauge (makes things easier)
|
|
|
|
aef
|
|
« Reply #11 on: November 22, 2016, 05:31:25 AM »
|
|
|
Start with a Mercedes Benz Sprinter Intercooler if this is a option for you.
|
|
|
|
|
Logged
|
|
|
|
dokalanyi
Full Member
Karma: +4/-1
Offline
Posts: 118
|
|
« Reply #12 on: November 22, 2016, 09:19:12 AM »
|
|
|
Start with a Mercedes Benz Sprinter Intercooler if this is a option for you.
Good suggestion actually -- seeing as we get all our spare parts by importing old cars used cars that have been "cut". So only OEM parts are available locally. The Benz intercooler looks front mount, fabricating that piping won't be trivial, unless sprinter pipes can be adapted. |
|
|
|
|
Logged
|
|
|
|
|
