Dev Blog
Forum
Wiki
About
NefMoto
>
Technical
>
NefMoto Software
>
Re: "failed to read test echo from FTDI device" error
Pages: [
1
]
« previous
next »
Author
Topic: Re: "failed to read test echo from FTDI device" error (Read 7687 times)
EuroXs4
Full Member
Karma: +15/-31
Offline
Posts: 209
Re: "failed to read test echo from FTDI device" error
« on: December 17, 2016, 09:43:01 PM »
I got the nefmoto to work.But now have a different issue.Cant connect to ecu with slow init.No matter what baud rate I use on the bench.
Logged
EuroXs4
Full Member
Karma: +15/-31
Offline
Posts: 209
Re: "failed to read test echo from FTDI device" error
« Reply #1 on: December 22, 2016, 05:50:07 PM »
Ok so long story short I got another ecu.But for the life of me I still can get nefmoto to read it.This is what I have now.This is being done on the bench with immo disabled.Ecu is a me7.5 8e0919518ak stock ecu.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Starting diagnostic session.
Disconnecting because no response was received for the Tester Present message.
Disconnected
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
Logged
nyet
Administrator
Hero Member
Karma: +604/-166
Offline
Posts: 12232
Re: "failed to read test echo from FTDI device" error
« Reply #2 on: December 22, 2016, 06:51:58 PM »
Probably not a stock flash.
Bootmode flash a stock AK file with galletto
Logged
ME7.1 tuning guide
(READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x
Please do not ask me for tunes. I'm here to help people make their own.
Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
EuroXs4
Full Member
Karma: +15/-31
Offline
Posts: 209
Re: "failed to read test echo from FTDI device" error
« Reply #3 on: December 24, 2016, 06:48:04 AM »
Already did.Then tried with nefmoto.Same thing.No change.The ecu I used I know was bone stock before i reflashed it with galletto.I cant communicate with the ecu even with vcds.Which leads me to believe either its bricked or stuck in bootmode??However when reading and writing in bootmode.No issues at all.Works fine.
Is it possible the ecu is stuck in bootmode???I read the flash with galletto.I DID NOT short pin 24 to ground.Just hooked up the ecu on the bench and read.Attached below.
«
Last Edit: December 24, 2016, 09:37:43 AM by EuroXs4
»
Logged
nyet
Administrator
Hero Member
Karma: +604/-166
Offline
Posts: 12232
Re: "failed to read test echo from FTDI device" error
« Reply #4 on: December 24, 2016, 11:15:53 AM »
That file is not stock
Code:
$ md5sum.exe bins/8E0909518AK-0003.bin 518AKnc.bin
de0521f258855661f27284d17dbc8907 *bins/8E0909518AK-0003.bin
bc80e7ef0e4cc918d7308be0edfd110f *518AKnc.bin
Logged
ME7.1 tuning guide
(READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x
Please do not ask me for tunes. I'm here to help people make their own.
Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Pages: [
1
]
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> Introductions
=> General Discussion
-----------------------------
Noob Zone
-----------------------------
=> Noob Questions
=> Noob Guides and FAQs
-----------------------------
Technical
-----------------------------
=> NefMoto Software
=> Tuning
===> Documents & Helpers & How To's
===> Community Projects
=> Diagnostics
=> Flashing and Chipping
=> Cluster and Immobilizer
===> ECU EEPROM images
===> Original Cluster dumps
===> Original Cluster dump requests
=> Data Logging
=> Reverse Engineering
=> Communication Protocols
-----------------------------
ECU Files
-----------------------------
=> ECU Definition Files
===> ECU Definition File Requests
=> Original ECU Files
===> Original ECU File Requests
=> Checksum Update Requests
-----------------------------
Vehicles
-----------------------------
=> Vehicle Tech
=> Project Cars
-----------------------------
Regional
-----------------------------
=> Canadian Regional Discussion
=> US Regional Discussion
-----------------------------
Classifieds
-----------------------------
=> For Sale
=> Wanted
=> Services
-----------------------------
Miscellaneous
-----------------------------
=> Off Topic
=> Forum Tech Support
=> Bizarro Messages Posted by Bots and Spammers
Navigation
Home
Help
Login
Register
Personal Tools
March 29, 2024, 02:58:09 AM
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Search
Advanced Search
Loading...