|
airtite
|
 |
« on: November 22, 2011, 11:02:03 PM »
|
|
|
Hi Guys
Please could someone have a look at the attached screenshot of my stock KFMIRL. I am trying to figure out if the xdf I am using is correct for my ecu. What I did last night is multiplied the whole KFMIRL table by 2 and then increased LDRXN and LDRXNZK accordingly to match. I took a test drive and logged lamda/mg/s and boost but my boost doesnt seem too have increased?
|
|
|
|
|
Logged
|
|
|
|
|
RaraK
|
|
« Reply #1 on: November 23, 2011, 06:07:09 AM »
|
|
|
Whoooooaaaa! STOP!
that is NOT correct
you need to edit that xdf to work with your file.
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #2 on: November 23, 2011, 06:12:30 AM »
|
|
|
thanks for the feedback, ok I would love too edit the xdf but I am batteling too figure out how too correlate the KFMIRL too a hex beginning and end?
attached are my original bin and the xdf I have, if someone could just give me a quick run down I am sure I will be able too be of some benefit too this forum.
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #3 on: November 23, 2011, 06:27:33 AM »
|
|
|
what I am trying is too edit the xdf parameter for KFMIRL, then take the address in hex for example 0x1E27C and then trying too search for that in winols so that I can see if there is anything that stands out.... but when I search for that hex address in any hexeditor or even winols its not being found.
|
|
|
|
|
Logged
|
|
|
|
|
Gonzo
|
|
« Reply #4 on: November 23, 2011, 06:39:59 AM »
|
|
|
Start analyzing patterns on other defined files and you fill find KFMIRL. KFMIRL is one of the easier maps to find.
Oh, and please flash back to stock ASAP!
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #5 on: November 23, 2011, 06:56:33 AM »
|
|
|
I have opened the TT ols files posted up here and the other defined maps are there but not KFMIRL?
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #6 on: November 23, 2011, 07:00:39 AM »
|
|
|
nevermind, click search maps  |
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #7 on: November 23, 2011, 07:47:56 AM »
|
|
|
sorry to be a pain but please could someone point out the pattern in the following... am I meant to be looking at the graphs on the right of the hex?
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #8 on: November 23, 2011, 08:03:02 AM »
|
|
|
please could someone tell me if this is perhaps it?
|
|
|
|
|
Logged
|
|
|
|
|
|
|
airtite
|
|
« Reply #10 on: November 23, 2011, 09:48:46 AM »
|
|
|
I think this is the correct map for KFMIRL? The x and y axis isnt correct though, how do I fix that?
|
|
|
|
|
Logged
|
|
|
|
|
Gonzo
|
|
« Reply #11 on: November 23, 2011, 10:17:06 AM »
|
|
|
I don't usually spoon feed but I'll upload some screenshots of a proper kfmirl defined map. Is this a tt225?
If you can't properly find these maps then you are prob not fit to be modifying anything though.
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #12 on: November 23, 2011, 10:50:12 AM »
|
|
|
thank you I appreciate your help....
|
|
|
|
|
Logged
|
|
|
|
|
Gonzo
|
|
« Reply #13 on: November 23, 2011, 10:52:16 AM »
|
|
|
What is this file off?
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #14 on: November 23, 2011, 10:59:57 AM »
|
|
|
its off a audi 1.8T 2002 and I think I may have cracked it!!! the winols interface is a little clunky but here is my first map
|
|
|
|
|
Logged
|
|
|
|
|
