maluch
Newbie
Karma: +0/-0
 Offline
Posts: 17
|
 |
« on: March 20, 2017, 02:21:59 PM »
|
|
|
Hello. I have a 2.7 biturbo engine from an 1999 A6. with a 2001 Allroad ecu with M box bin, and with immo off. And tfsi coils. The engine is mounted in a racecar, and I have used the orginial harness and the cluster from the A6.
My trouble is that the ecu don't send ground to the fuel pump relay when ignition is turned on, it sends ground when I cranking so fuel pump and the sensors getting power at cranking. And i got no spark at the coils. The coils have power and ground(x2)
The faults in the memory is no communication with ABS, and with instrument cluster. I have wired opp the correct wires to the cluster from the ecu, EPC lamp comes on when I turn on ecu power.But is allroad communication through CAN? and do I need termination resistor at the computer?
Somebody have som ideas? Have check the entire harness from every sensor to the connector at the ecu, check power and ground, everything is okay.
any ideas is appreciated.
Thanks
|
|
|
|
« Last Edit: March 29, 2017, 01:37:41 PM by maluch »
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +186/-24
Offline
Posts: 1456
mk4 1.8T AUM
|
|
« Reply #1 on: March 20, 2017, 03:09:23 PM »
|
|
|
check coils wiring
+12v from ignition, 2x ground (check for good chassis connection), and signal from ecu at coils and injectors when cranking (ecu sends ground iirc)
|
|
|
|
« Last Edit: March 20, 2017, 04:01:25 PM by fukenbroken »
|
Logged
|
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #2 on: March 20, 2017, 03:11:49 PM »
|
|
|
coils wiring is all new. what kind of signal is the ecu give to the coils?
The injectors is working, the plugs getting wet when I crank.
|
|
|
|
|
Logged
|
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #3 on: March 21, 2017, 10:58:01 AM »
|
|
|
Just tried to upload a stock D box. The only fault in memory now is communication to ABS. But it primed the 2 first times. But o spark.
Ideas?
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +186/-24
Offline
Posts: 1456
mk4 1.8T AUM
|
|
« Reply #4 on: March 21, 2017, 12:19:31 PM »
|
|
|
have you test it for a spark? (insert the spark plug into the coil, put it on the engine cover to connect spark plug ground to the engine ground and ask someone to crank)
if no spark, check signal wire to the coil.
|
|
|
|
|
Logged
|
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #5 on: March 21, 2017, 12:37:42 PM »
|
|
|
Yes, I have check that, with a new sparkplug also, and I have measured between the coils and ecu connector. the trigger signal is connected to the coils from pin 94, 95, 102, 103 110 and 111 on the ecu connector.
|
|
|
|
|
Logged
|
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #6 on: March 21, 2017, 01:35:43 PM »
|
|
|
|
|
|
|
« Last Edit: March 27, 2017, 10:16:09 AM by maluch »
|
Logged
|
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #7 on: March 22, 2017, 12:53:59 PM »
|
|
|
One more thing. The engine is hooked up to a A4 1.8t 016 gearbox, is the crankshaft sensor at the exactly the same place as in a S4 B5 01E gearbox?
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #8 on: March 22, 2017, 02:22:24 PM »
|
|
|
When you crank the car, can you see the rpm gauge raise slightly?
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #9 on: March 22, 2017, 02:28:05 PM »
|
|
|
I don't think so. but i'm not 100% sure.
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #10 on: March 22, 2017, 02:58:55 PM »
|
|
|
If you look closely, it will be pretty obvious. You can also log in with a scan tool, and see if it shows rpm while cranking.
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #11 on: March 22, 2017, 03:02:29 PM »
|
|
|
with scan tool i got around 160-170 rpm when cranking. so its picking up from the crankshaft sensor.
|
|
|
|
|
Logged
|
|
|
|
maluch
Newbie
Karma: +0/-0
Offline
Posts: 17
|
|
« Reply #12 on: March 26, 2017, 10:18:57 AM »
|
|
|
nobody?
The epc lamp is lit with igntion on, and is going out after the engine has cranked for 1 sec or something.
And if I upload a different bin file to the ECU, the first times I put on the ignition, it primes the fuel pump, but does this only 1 or 2 times. then it won't prime. And it will not start when is priming either, no spark at all.
Have check the wiring 10 times now I think. everything lookes like it is in order. but still no start.
Thinking maybe throwing that crappy Motronic and buying a standalone!
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +186/-24
Offline
Posts: 1456
mk4 1.8T AUM
|
|
« Reply #13 on: March 26, 2017, 07:08:24 PM »
|
|
|
its ok about ignition / fuel pump activity
you didnt answer about signal from ecu to coils. have you check it?
if there is pulses appears when cranking and no spark then check coils wiring / replace one coil with a new unit. ive seen once an 1.8t with no spark. signal ok, +12 ok, 2x ground ok. no spark.. the problem was in bad ground connection. you should check wiring under load to find a problem in that case
if no signal from ecu then there was an dtcs usually
check fuses also, there is one for ecu to coils
btw pictures are invisible
|
|
|
|
« Last Edit: March 26, 2017, 07:10:23 PM by fukenbroken »
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #14 on: March 27, 2017, 03:24:47 AM »
|
|
|
Did the ECU run in a previous setup?
|
|
|
|
|
Logged
|
|
|
|
|
