Pages: [1]
Author Topic: Cluster 8L0920931F - Tuning in eeprom (needles&scales)  (Read 4913 times)
vara82
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 64


« on: November 24, 2017, 02:07:38 AM »

Hey Guys...
Is it possible to switch on Lights from needles and/or scales with turning on ignition by changing some bits in eeprom?!
Perhaps it´s possible that needles going up&down (initializing) when tunring on ignition?!

I know from various Golf 4 cluster that i have to change one bit in the eeprom to turn on lights, welcome message and so on...

I´ve a Cluster from Audi A3 2002, too... There i can switch on the lights over diagnostics Channel 19... But at actual cluster Channel 19 doesn´t exist.

It´s a 8L0920931F (VDO) from a 2000 Audi A3 1.8t.

Dump from Cluster attached...

Best regards,
Flo
Logged
macxxx
Sr. Member
****

Karma: +29/-1
Offline Offline

Posts: 498


« Reply #1 on: November 24, 2017, 05:55:04 AM »

In Audi it is only possible on clusters from MY2002 to set the needles to light up on ignition , and no possibility of needle sweep.

On your 2000 cluster you can only set to light the scales and needles together on ignition , with or without switches.


The adres you are looking for is $1DE- the default od 35 , you should try changing the second position like 3D , 31 etc
Logged
vara82
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 64


« Reply #2 on: November 24, 2017, 10:55:02 AM »

Hey macxxx,
thanks for your help... It´s okay for me if it´s possible to light up Scales and Needles together with ignition...

But i can´t found the default value (35) in 1ED location...

Please take a look at the picture i attached...

Can you please mark the location i´ve to change?!

Logged
vara82
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 64


« Reply #3 on: November 24, 2017, 10:58:23 AM »

Sorry... I´ve posted the wrong file... Sad

Here it is from my Audi Cluster...
Logged
macxxx
Sr. Member
****

Karma: +29/-1
Offline Offline

Posts: 498


« Reply #4 on: November 24, 2017, 02:05:07 PM »

Look at 1DE its 35 ( i made a typing mistake , swapped letters )
Logged
vara82
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 64


« Reply #5 on: November 24, 2017, 02:10:01 PM »

Yeah thanks... I saw the 35 in 1DE but i was not sure if i should change something there...

Have i to correct checksums before flashing the file back to cluster?! Or can i change the file and flash it without any corrections without cluster is damaged?

Logged
macxxx
Sr. Member
****

Karma: +29/-1
Offline Offline

Posts: 498


« Reply #6 on: November 24, 2017, 02:33:12 PM »

Checksum is in the speedomap so dont worry
Logged
vara82
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 64


« Reply #7 on: November 24, 2017, 02:35:52 PM »

Okay cool...
I´ll test it tomorrow and will give a report... Wink

Logged
vara82
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 64


« Reply #8 on: November 25, 2017, 02:42:01 PM »

Hello macxxx,

here´s my report:

3D is the solution...

I tried a little wirh another digits but it won´t happen so much...

With "3D" at "1DE" Scales, Displays and Needles light up with ignition.

Perfect, much thanks for your help!!!
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 17 queries. (Pretty URLs adds 0s, 0q)