Pages: [1]
Author Topic: EDC15VM Checksum disable for OLS300  (Read 7132 times)
ecossetuning
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« on: November 28, 2017, 02:24:46 PM »

Hi people Ive bought an ols300 and plan on using on 2.5 VW T4 edc15vm.

I'm told that to live tune/change on this i will need to disable the checksums, i dont know where to start with checksum disable is there anyone able to assist with this?

thanks

KP
Logged
scalp06
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 33


« Reply #1 on: November 30, 2017, 08:18:17 AM »

Hi, do you have already test it with standard chks correction in ols?

I use it on another ecu without disable chks and all is fine (only a quick reboot ecu when change data...)
Logged
ecossetuning
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #2 on: December 13, 2017, 02:50:20 PM »

yes i tried with it but it cuts out quite alot and with checksum disabled would be awesome for live mapping
Logged
gt-innovation
Sr. Member
****

Karma: +60/-89
Offline Offline

Posts: 442


« Reply #3 on: December 14, 2017, 07:15:49 AM »

yes i tried with it but it cuts out quite alot and with checksum disabled would be awesome for live mapping

You need to put ecu into test mode(from eeprom) and i suppose the same test mode applies to edc15 as in Me7

Look for CWNOROMCHKRESET as well in your definitions.

The test mode on me7 is on page 1 and page 2 of the eeprom and if you post i can see if it could be done on edc15
or search for (in hex ) the values  69,C1, and A5.


If you search a bit in the forum you will find this method that was posted from other members.
Logged
jochen_145
Full Member
***

Karma: +9/-4
Offline Offline

Posts: 177


« Reply #4 on: December 14, 2017, 07:48:36 AM »

Look for CWNOROMCHKRESET as well in your definitions

I never worked on this, CWNOROMCHKRESET is not part of EDC15V defintions AFAIS Sad

Quote
The test mode on me7 is on page 1 and page 2 of the eeprom and if you post i can see if it could be done on edc15
This seems to be equal to ECD15:
CS-test will start while initialisation and then goes on with a periodical backround test

AFAIR in MSA12/15, there was only a intialisation test and no backround test. So after ones CS-test pasted, you could chance every bit of flash without CS-error

So IMO you need to switch of periodic backround test..

Here you find the same "problem":

http://nefariousmotorsports.com/forum/index.php?topic=12846.0
Logged
jochen_145
Full Member
***

Karma: +9/-4
Offline Offline

Posts: 177


« Reply #5 on: December 14, 2017, 08:07:26 AM »

Found the link to ECUCONNECTIONS.COM-forum of diable CS of EDC15 again:

http://www.ecuconnections.com/forum/viewtopic.php?f=211&t=49704&sid=5cf324c44d2c74d372984f428ffea5ed

Logged
john9357
Full Member
***

Karma: +10/-1
Offline Offline

Posts: 54


« Reply #6 on: December 17, 2017, 02:10:20 AM »

on edc15p or vm, to disable "live" checksum, put "3d d3 3d d3" instead of "c3 c3 c3 c3" at address 0x70b76 (or 60b76/50b76)
, on msa15 at adress 0x38B76.
When you mod this, only the checksum at motor start must be exact, the checksum verification when motor run are disabled.
« Last Edit: January 06, 2018, 11:27:12 AM by john9357 » Logged
ecossetuning
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #7 on: January 13, 2018, 01:42:00 PM »

Hey Guys Thanks for the input.

I looked for the C3 C3 C3 C3 and can see these within ecu sw but when I changed it didn't make any difference, After making so many changes the ecu or should I say the ep2 needs a reflash to bring it back to life.

I will try and look in the file now that ive got some time away from ols300.

really appreciate the help guys.
 
Logged
ecossetuning
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #8 on: January 13, 2018, 01:47:36 PM »

here is the sw I am working on currently
Logged
ecossetuning
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #9 on: January 13, 2018, 02:04:20 PM »

Think maybe seen as this uses the syncblock 5XXXX that maybe the C3 C3 C3 C3 at 58B76 is what we need to change, will try it and report back.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.023 seconds with 16 queries. (Pretty URLs adds 0s, 0q)