NefMoto > Technical > Reverse Engineering > ME 7.8 code on 7.8.1 HW?
Pages: [1]
« previous next »
Author Topic: ME 7.8 code on 7.8.1 HW?  (Read 6970 times)
zweistein
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 19
« on: April 02, 2018, 08:11:07 AM »
Hello,

I have currently a Bosch 7.8.1 HW (from Porsche 987 or 997 )  and I would like to load the sw from a Porsche 996 tt on it.

The  older ME7.8 is very similar to the newer Me7.8.1 HW.  (newer ME7.8.1 has an empty socket for a Bosch IC30344 you can solder in)
Most pin connectors are identical (ignition coils and EV and most other sensors).

Both have the Siemens 80166 processor.

Will it be possible to load the 996tt code onto the Bosch 7.8.1 Hardware? (Ok , with Galletto will load, but:
Will it run there ?


Open questions are:

24 MHZ against 40 MHZ. cpu:  I would need to access the SY_FREQCPU constant (and a few related fields).  Known?

5p08 EEPROM access:   Epprom data structure is identical in several areas, but not everywhere.  Will the older ME7.8 pass the security codes on the CAN bus ?

IDA questions:  I am just a newcomer here. Could someone give me a hint to a correct C167 ROM file, or is this contained in a certain (32K ?) area in the flash. If yes , where?

Would be very happy to get some advice to startup quicker.
Will share my results here.

Thank you
andre
Logged
prj
Hero Member
*****

Karma: +1072/-480
Offline Offline

Posts: 6035
« Reply #1 on: April 02, 2018, 08:15:39 AM »
Short answer no.
Instead maybe explain what you are trying to accomplish.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
zweistein
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 19
« Reply #2 on: April 02, 2018, 09:57:09 AM »
Have a Porsche Cayman with bi turbo setup.   Running fine for several years with 987S mapped ecu, but occasionally I get DTC from the torque monitor which are caused by the charged air column inertia.   ECU goes in limp mode then and needs to be reset with Durametric or Piwis.

Would like to add N75 support and possibly all the 996tt support (wide band lambda...) into the ECU.

Where do you see the biggest problems?

Would it be easier to start from a 996tt ECU and then modify the 5p08 eeprom to get the PAS security up and running?
Logged
zweistein
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 19
« Reply #3 on: April 02, 2018, 01:15:31 PM »
Have to correct:
I am interested to interchange a ME7.8 from a 996tt with a ME7.8 from a 987 or 997 NA car.
NOT interested in 997tt


Quote from: zweistein on April 02, 2018, 09:57:09 AM
Have a Porsche Cayman with bi turbo setup.   Running fine for several years with 987S mapped ecu, but occasionally I get DTC from the torque monitor which are caused by the charged air column inertia.   ECU goes in limp mode then and needs to be reset with Durametric or Piwis.

Would like to add N75 support and possibly all the 996tt support (wide band lambda...) into the ECU.

Where do you see the biggest problems?

Would it be easier to start from a 996tt ECU and then modify the 5p08 eeprom to get the PAS security up and running?
Logged
prj
Hero Member
*****

Karma: +1072/-480
Offline Offline

Posts: 6035
« Reply #4 on: April 02, 2018, 02:17:26 PM »
So just swap the ECU and kill or adapt the immobilizer.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
nubcake
Sr. Member
****

Karma: +53/-4
Offline Offline

Posts: 400
« Reply #5 on: April 02, 2018, 03:42:48 PM »
+1 to what prj said.

Immo is relatively easy to delete on these.
Check public 7.8 A2L and look for "WFS" routines.
Basically it's starter lockout, fuel pump lock and spark IIRC.

Could be relatively easy to adapt it as well, but never researched that.
Logged
rsm1
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8
« Reply #6 on: December 12, 2018, 04:23:22 AM »
hi
sorry to  butt in....

as i see the last person who replied could possibly help me too...
im looking to disable the immo on an me7.8...with bosch number 0261207987...its a 3.4 caymen...its got an eprom 35p08
can you tell me if i do it the same as awe do the Me7.xx on Vags..will it work?

i can upload the eprom if needed if you can do the immo off for me?

thanks alot for the help...
Logged
rsm1
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8
« Reply #7 on: December 12, 2018, 04:32:40 AM »
Quote from: prj on April 02, 2018, 02:17:26 PM
So just swap the ECU and kill or adapt the immobilizer.

hi
thats what im looking for this type of porsche ecu to do..immo off...me7.8....0261207987...can you help me on this ..i know its in the eprom..35p08..
what do i change?
is it like the typical vag..me7.5?
would appreciate the help.
thanks
Logged
stuklr
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 147
« Reply #8 on: May 14, 2024, 07:12:16 AM »
Quote from: nubcake on April 02, 2018, 03:42:48 PM
+1 to what prj said.

Immo is relatively easy to delete on these.
Check public 7.8 A2L and look for "WFS" routines.
Basically it's starter lockout, fuel pump lock and spark IIRC.

Could be relatively easy to adapt it as well, but never researched that.


Is it really as easy as zeroing CDKWFS? or maybe CDTWFS? both are listed as immo codewords
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 22, 2024, 07:44:18 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.018 seconds with 17 queries. (Pretty URLs adds 0s, 0q)