Pages: [1]
Author Topic: Car wont start after sitting for a month, cranks , battery fine  (Read 6676 times)
Ptyrell
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 30



Hi guys,

My B4 S4 wont start , was sitting for a month or so cranks fine, charged and swapped batteries.

Have this DTC

Address 17: Instruments        Labels: 8D0-920-xxx-17.lbl
   Part No: 8D0 920 930 F
   Component: B5-KOMBIINSTR. VDO D07   
   Coding: 02764
   Shop #: WSC 00222 
   VCID: 29538C00D3E23D6

   Component: AUZ7Z0X1160367 
   ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ     AUZ7Z0X1160367

1 Fault Found:
01177 - Engine Control Unit
            49-00 - No Communications

Any ideas?
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2802



« Reply #1 on: April 28, 2018, 07:05:29 PM »

Hi guys,

My B4 S4 wont start , was sitting for a month or so cranks fine, charged and swapped batteries.

Have this DTC

Address 17: Instruments        Labels: 8D0-920-xxx-17.lbl
   Part No: 8D0 920 930 F
   Component: B5-KOMBIINSTR. VDO D07   
   Coding: 02764
   Shop #: WSC 00222 
   VCID: 29538C00D3E23D6

   Component: AUZ7Z0X1160367 
   ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ     AUZ7Z0X1160367

1 Fault Found:
01177 - Engine Control Unit
            49-00 - No Communications

Any ideas?

well it would help if you scanned the ecu and not the cluster to start.
Logged

Giving your mom a tuneup
Ptyrell
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 30


« Reply #2 on: April 28, 2018, 07:19:59 PM »

That's the only error, I did scan the ECU as a single module and it had no errors. I can also read/write to the flash
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2802



« Reply #3 on: April 28, 2018, 07:28:06 PM »

fuel pump running while cranking? if not relay / bad pump. is the cel on when you tun the key on? if not then missing switched power to ecu
Logged

Giving your mom a tuneup
Ptyrell
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 30


« Reply #4 on: April 28, 2018, 09:28:19 PM »

Thanks mate for the reply, I will get someone to crank while I listen for the fuel pump priming.

I have no CEL lights on dash, says OK
Logged
Ptyrell
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 30


« Reply #5 on: April 28, 2018, 11:26:53 PM »

Cant hear the fuel pump , put a phone in there while put key to position 2 just before start. Also cranked it, nothing on phone. Its a Walbro 450 , so its pretty loud. Only done few hundred km,

I can hear relays behind the dash etc.

When the key is on position 2 (not crank) the EPC and battery light is on. If I crank then stop they go away and OK is on the display

Checked the fuses also.  Not looking forward to pulling the fuel pump out Tongue
Logged
Ptyrell
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 30


« Reply #6 on: April 29, 2018, 08:58:26 PM »

Here is a video of key on no crank

https://youtu.be/-PThEYR_y2s

I can read the cluster eeprom and use MElogger as normal
Logged
Ptyrell
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 30


« Reply #7 on: April 29, 2018, 09:28:29 PM »

Is there anyway my cluster programing has freaked? I was on H box and the ecu tune is based on M box

Nah looked at it ok
« Last Edit: April 29, 2018, 10:24:32 PM by Ptyrell » Logged
Ptyrell
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 30


« Reply #8 on: April 30, 2018, 07:56:24 AM »

fuel pump running while cranking? if not relay / bad pump. is the cel on when you tun the key on? if not then missing switched power to ecu


What relay controls the switched power to the ecu?
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 16 queries. (Pretty URLs adds 0.001s, 0q)