NefMoto > Technical > Tuning > MED9.1 High EGT after changing turbo
Pages: 1 [2]
« previous next »
Author Topic: MED9.1 High EGT after changing turbo  (Read 11444 times)
gman86
Hero Member
*****

Karma: +45/-128
Offline Offline

Posts: 705
« Reply #15 on: April 30, 2018, 04:58:49 PM »
Log 091 and see what the cam is up to
Logged
Khendal
Full Member
***

Karma: +9/-8
Offline Offline

Posts: 226
« Reply #16 on: May 01, 2018, 04:42:09 AM »
Quote from: gman86 on April 30, 2018, 04:58:49 PM
Log 091 and see what the cam is up to
For what? What are you thinking ?
Logged
gman86
Hero Member
*****

Karma: +45/-128
Offline Offline

Posts: 705
« Reply #17 on: May 01, 2018, 02:04:37 PM »
Quote from: Khendal on May 01, 2018, 04:42:09 AM
For what? What are you thinking ?

Overlap can induce higher EGTs.
Logged
Bitshifter
Full Member
***

Karma: +10/-7
Offline Offline

Posts: 94
« Reply #18 on: May 02, 2018, 11:40:26 PM »
How do you measure EGT? Dit you install a K-Type and loop it in the ECU or is your group 230 only the a produkt of KFATMKRH?
Logged
mbkr89
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 96
« Reply #19 on: May 08, 2018, 01:38:30 AM »
How you run 170 bar rail pressure ?
Is it ea888 engine ?
Logged
Khendal
Full Member
***

Karma: +9/-8
Offline Offline

Posts: 226
« Reply #20 on: May 08, 2018, 03:14:27 PM »
Quote from: gman86 on May 01, 2018, 02:04:37 PM
Overlap can induce higher EGTs.

But the problem happened only after have changed turbo...from 3071 to 3076  Undecided
Logged
Khendal
Full Member
***

Karma: +9/-8
Offline Offline

Posts: 226
« Reply #21 on: May 08, 2018, 03:22:55 PM »
Quote from: Bitshifter on May 02, 2018, 11:40:26 PM
How do you measure EGT? Dit you install a K-Type and loop it in the ECU or is your group 230 only the a produkt of KFATMKRH?

K-type probe  Wink
Logged
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick
« Reply #22 on: May 08, 2018, 04:14:55 PM »
Quote from: Khendal on April 29, 2018, 03:25:49 AM
All exhaust system is 76mm at the moment... he will upgrage to 80mm or 90mm asap.
They are not talking about your exhaust, but about the restriction of the turbine. What is the size of the turbine housing?
You are trying to cram more air through the same hole as before with this larger turbo, and as you may know higher pressure = higher temperature. The tips to combat EGT are usefull like more efficient ignition angle and extra fuel for cooling, but there is logic to the cause too.
Logged
My project (all photos back online!)
prj
Hero Member
*****

Karma: +1072/-481
Offline Offline

Posts: 6037
« Reply #23 on: May 09, 2018, 02:18:25 AM »
Even worse - because the compressor wheel is now larger, the CHRA spins slower to produce a certain amount of boost.
That also means that turbine flow is less for a given boost pressure - this increases exhaust pressure even more.

If you have a 0.63 housing you need to go to a 0.82.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
Pages: 1 [2]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 27, 2024, 06:41:32 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.018 seconds with 17 queries. (Pretty URLs adds 0s, 0q)