Pages: [1]
Author Topic: traction control without MAF sensor? me7.5  (Read 4348 times)
up50lut3
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 55


« on: May 04, 2018, 02:03:29 PM »

hey guys,

as title states. is it possible to still have active traction control when running without a maf sensor?

AWP 1.8t me7.5

with the maf not installed the t/c light is on and always disabled. is there any effective coding or variables i can chage to eliminate this from happening and the switch still work?? thanks in advaced!
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2802



« Reply #1 on: May 04, 2018, 05:47:53 PM »

It was discussed a few times. It's called the asr hack. You kill the error message reported to can and unless you can figure that out on your own I doubt anyone e will reveal how. Alternatively you can change the abs module coding (mk60 modules). You can also log into canbus and disable abs to hide the lights. Both are a hack and I dont reccomend doing it those ways. Master of fact all of it's a hack
Logged

Giving your mom a tuneup
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2802



« Reply #2 on: May 04, 2018, 05:54:26 PM »

It was discussed a few times. It's called the asr hack. You kill the error message reported to can and unless you can figure that out on your own I doubt anyone e will reveal how. Alternatively you can change the abs module coding (mk60 modules). You can also log into canbus and disable abs to hide the lights. Both are a hack and I dont reccomend doing it those ways. Master of fact all of it's a hack

Also in other discussion on other forums  a member said setting some flow at zero volts on the maf table keeps the maf signal low from triggering so it keeps asp working. I haven't tried this myself so I cant confirm that tho. So may not need to set claim? Idk pissibly someone else can add more ?
Logged

Giving your mom a tuneup
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12270


WWW
« Reply #3 on: May 04, 2018, 07:30:48 PM »

Why on earth are you running no MAF on an ECU that can't do speed density?
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2802



« Reply #4 on: May 05, 2018, 05:25:27 AM »

Why on earth are you running no MAF on an ECU that can't do speed density?
as long as your fueling is super dialed in closed loop lambda hasnt ever let me down.
Logged

Giving your mom a tuneup
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12270


WWW
« Reply #5 on: May 05, 2018, 09:55:54 AM »

as long as your fueling is super dialed in closed loop lambda hasnt ever let me down.

Except when the ENTIRE of the rest of the ECU depends on load to make decisions. See also: the OP

Sure, it works "OK", but you'll be chasing gremlins forever. Or just ignore them and say "OMG i'm running speed density so I'm fast" when you really mean "limp mode alpha-n".
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
up50lut3
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 55


« Reply #6 on: May 05, 2018, 07:48:57 PM »

Why on earth are you running no MAF on an ECU that can't do speed density?

Im not.. Im still using one... Just a question..... Relax good sir

Whats that game called... Jump

To conclusions lol
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.016 seconds with 17 queries. (Pretty URLs adds 0s, 0q)