Pages: [1]
Author Topic: Powering the ECU for my B6 2.7T Swap... Need B5 S4 help  (Read 9837 times)
AudiA4_20T
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 18


« on: January 24, 2012, 09:33:23 AM »

Hey guys, so I have the car almost done and it's just about started

http://www.youtube.com/watch?v=4XdwODnsrfQ

But it's not getting fuel, meaning the ECU isn't triggering the fuel pump relay, meaning the ECU might not be on, meaning that I might have my wiring wrong...

Using this diagram



I have pin 62 getting the 30 terminal, but it says pin 3 gets the 15 terminal (switched power), which looks like the black wire with the blue stripe. On the B6 the same wire seems to not go to switched power?
« Last Edit: January 24, 2012, 09:35:19 AM by AudiA4_20T » Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3


« Reply #1 on: January 24, 2012, 12:11:09 PM »

If I recall correctly, pin 3 is switched power based on the ignition.

You should attempt to communicate with the ECU via NefMoto or VAG-COM to make sure it is powering up.
Logged

Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
AudiA4_20T
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 18


« Reply #2 on: January 24, 2012, 02:47:12 PM »

Yea, wish I could make a bench harness. Unfortunately I don't. When I get down to the shop I might have one. We will see.
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3


« Reply #3 on: January 24, 2012, 02:55:18 PM »

Yea, wish I could make a bench harness. Unfortunately I don't. When I get down to the shop I might have one. We will see.

Can't you just use the OBD port on the car?
Logged

Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
RaraK
Hero Member
*****

Karma: +58/-2
Offline Offline

Posts: 539


« Reply #4 on: February 06, 2012, 10:05:12 AM »

I found OP's original post, here it is because i immediately got excited when i saw B6 and 2.7tt Tongue

http://www.audizine.com/forum/showthread.php/428506-Clint-s-B6-2-7T-Build-Swap
Logged
Aragorn
Full Member
***

Karma: +3/-0
Offline Offline

Posts: 94


« Reply #5 on: February 15, 2012, 08:16:48 AM »

Why are you even looking at connections on the ECU?

The stock harness just plugs into the ECU and shouldnt need touched.

The connections all should be made at the 5 multipin plugs that join the engine harness to the car.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.037 seconds with 17 queries. (Pretty URLs adds 0s, 0q)