Pages: [1]
Author Topic: Audi S3 - CDLA - MED9.1 - Intake manifold flaps remove  (Read 6093 times)
sieniu
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« on: July 13, 2018, 10:35:21 AM »

Hello, i'm looking for some help how to remove intake flaps from soft. My soft is 8P0 907 115 AP, file in attachment. I find on forum that i have to look for :

CLALBK
CLALBKE
CLALBKO
CLALBKP

But the problem is that i can find this in my file. I have damos from med9.1 but is little different and i can't find this bytes.

And another question, after remove flaps car have problem with idle at cold engine, what advice ?

thanks for help.
Logged
gt-innovation
Sr. Member
****

Karma: +60/-89
Offline Offline

Posts: 442


« Reply #1 on: July 13, 2018, 11:26:35 AM »

Hello, i'm looking for some help how to remove intake flaps from soft. My soft is 8P0 907 115 AP, file in attachment. I find on forum that i have to look for :

CLALBK
CLALBKE
CLALBKO
CLALBKP

But the problem is that i can find this in my file. I have damos from med9.1 but is little different and i can't find this bytes.

And another question, after remove flaps car have problem with idle at cold engine, what advice ?

thanks for help.

Consider removing your flaps with stock turbo or similar to stock turbo useless and bad for your fuel efficiency...
Logged
Kacza
Full Member
***

Karma: +20/-6
Offline Offline

Posts: 213


« Reply #2 on: July 13, 2018, 12:26:47 PM »

Hello, i'm looking for some help how to remove intake flaps from soft. My soft is 8P0 907 115 AP, file in attachment. I find on forum that i have to look for :

CLALBK
CLALBKE
CLALBKO
CLALBKP

But the problem is that i can find this in my file. I have damos from med9.1 but is little different and i can't find this bytes.

And another question, after remove flaps car have problem with idle at cold engine, what advice ?

thanks for help.


These bits should be excluded from the DTC table. If you do not have a lady for your ECU, you have to calculate their addresses because another damos has a different DTC table layout.
Logged
sieniu
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #3 on: July 14, 2018, 12:11:48 AM »

Thanks for answer but what with this problem with idle at cold engine ?
Logged
cherry
Full Member
***

Karma: +23/-2
Offline Offline

Posts: 245


« Reply #4 on: July 14, 2018, 01:27:36 AM »

Mechanical issue because streaming air is low speed then without flaps. Turbolence air/fuel is bad, combustion is bad. I think it can be improved by tweaking injection timing, but it does not make any sense to remove them unless you have cheap aftermarket manifold.
Logged
sieniu
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #5 on: July 15, 2018, 12:47:39 PM »

Can someone help with some changes in soft ? What maps to change?
Logged
konkat
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 5


« Reply #6 on: July 16, 2018, 07:02:45 AM »

Injection timing, injection start angle limiter, warmup fuel correction, lambda target vs temperature, intake charge flap control, fuel rail pressure
Logged
purepower
Newbie
*

Karma: +5/-1
Offline Offline

Posts: 22



« Reply #7 on: July 22, 2018, 09:08:41 AM »

Hello, i'm looking for some help how to remove intake flaps from soft. My soft is 8P0 907 115 AP, file in attachment. I find on forum that i have to look for :

CLALBK
CLALBKE
CLALBKO
CLALBKP

But the problem is that i can find this in my file. I have damos from med9.1 but is little different and i can't find this bytes.

And another question, after remove flaps car have problem with idle at cold engine, what advice ?

thanks for help.

Try to check here. DTC removed also.

PurePower
Logged

PurePowerPerformance
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #8 on: July 23, 2018, 07:46:32 AM »

Mechanical issue because streaming air is low speed then without flaps. Turbolence air/fuel is bad, combustion is bad. I think it can be improved by tweaking injection timing, but it does not make any sense to remove them unless you have cheap aftermarket manifold.

Why did you ignore this post, OP?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 18 queries. (Pretty URLs adds 0s, 0q)