Pages: [1]
Author Topic: help with rear 02's mk4 r32( have some locations already)  (Read 3952 times)
up50lut3
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 55


« on: July 29, 2018, 11:58:11 PM »

hey all,

i can't find a damos or xdf for my ecu.. ive tried others to compare but to no avail.

I still have the rear 02's but no cats. i can either delete them or numb them to go through emissions but i cant figure out which bit is what for ither situation

anyone with a little insight as to whats what would be much appreciated

0x18194 is where control bits start.

i have the are where the control bits are but cant find the correct addresss for

You maybe able to numb ME7's sensitivity (note: untested) using: [55][56]

AHKATMN (0x18672) - leave alone
AHKATMX (0x18673) - set to max
AHKATS (0x18674) - set to max
AHKATSB (0x18675) - set to max

....or


 CDHSH - Post cat O2 heater diagnosis
CDHSHE - Post cat O2 heater amplifier diagnosis
CDLATV - Lambda sensor aging diagnosis (tv) in OBDII-Mode (inverse: EURO-Mode)
CDLASH - Lambda sensor aging diagnosis (SHK) in OBDII-Mode (inverse: EURO-Mode)
CDLSH - Post cat O2 sensor diagnosis
CDLSHV - Lambda sensor sensor interchange recognition (N/A for vehicles equipped with a single post cat sensor, IE 1.8t and certain vr6)
CWKONLS (0x181BB) - Vehicles with 4 installed sensors - change from 51 (0x33/00110011b) to 17 (0x11/00010001b)[58] Vehicles with 2 installed sensors (default value 3), set to 1. When setting CWKONLS CDLSH must also be configured to prevent malfunction in circuit DTC's.
CWKONLS.1 = 0
CWKONLS.5 = 0
Change these to disable rear O2 lambda control:[59][60]

CLRHK (0x11A87) - Code word for Lambda - Bit 0 is Control post cat on/off. Set bit 2 and 0, clear bit 3 to disable; i.e. set from 72 (0x48/01001000b) to 5 (00000101b)[61]
CLRHK.0 = 1
CLRHK.2 = 1
CLRHK.3 = 0
CLRHK.6 = 0 (don't care)
CLRSHK - Wideband vehicles use CLRSHK. In these the default value is typically 16 (0x10/0001000b). Set bit 0 (and possibly set bit 2 and clear bit 3?) to disable (set to 5?)
CLRSHK.0 = 1
CLRSHK.2 = 1(?) unconfirmed.
CLRSHK.3 = 0(?) unconfirmed.
CLRKA (0x11A72) - set to 0[62]
Logged
J.Laborde
Full Member
***

Karma: +57/-29
Offline Offline

Posts: 82


Tuner and Software Developer


WWW
« Reply #1 on: July 30, 2018, 12:09:25 AM »

Hey Mate,

I'll take a look at your file in a few hours, and export a map pack with all the maps you're after Smiley

~ J.Laborde
Logged

I am here to learn and help others learn. Smiley

He's a maniac.......MAAAAAANIIIAC
up50lut3
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 55


« Reply #2 on: July 30, 2018, 12:30:35 AM »

love you.... no homo lol
 Roll Eyes Roll Eyes
Logged
up50lut3
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 55


« Reply #3 on: July 30, 2018, 04:12:08 PM »

love you.... no homo lol
 Roll Eyes Roll Eyes

so i guess that was bs..... Sad(
Logged
J.Laborde
Full Member
***

Karma: +57/-29
Offline Offline

Posts: 82


Tuner and Software Developer


WWW
« Reply #4 on: July 30, 2018, 05:58:42 PM »

Hey mate,

Some shit came up yesterday... If you message me I'll keep you updated.
Logged

I am here to learn and help others learn. Smiley

He's a maniac.......MAAAAAANIIIAC
J.Laborde
Full Member
***

Karma: +57/-29
Offline Offline

Posts: 82


Tuner and Software Developer


WWW
« Reply #5 on: July 31, 2018, 12:33:31 AM »

Hello  Smiley ,

Attached is your R32_EG file with the entire Project Konfiguration table defined in an OLS, compatible with WinOLS 2.24/2.26.
I can give you an entire map pack in english specially designed for Stage 1/ Stage 2 tuning if you're happy to pay for it.

~J.Laborde
Logged

I am here to learn and help others learn. Smiley

He's a maniac.......MAAAAAANIIIAC
vwdubNam
Jr. Member
**

Karma: +1/-0
Offline Offline

Posts: 27


« Reply #6 on: July 31, 2018, 03:29:30 AM »

Hello  Smiley ,

Attached is your R32_EG file with the entire Project Konfiguration table defined in an OLS, compatible with WinOLS 2.24/2.26.
I can give you an entire map pack in english specially designed for Stage 1/ Stage 2 tuning if you're happy to pay for it.

~J.Laborde
i'll in box you. i realkly just need that
Logged
up50lut3
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 55


« Reply #7 on: August 07, 2018, 09:56:12 AM »

Hello  Smiley ,

Attached is your R32_EG file with the entire Project Konfiguration table defined in an OLS, compatible with WinOLS 2.24/2.26.
I can give you an entire map pack in english specially designed for Stage 1/ Stage 2 tuning if you're happy to pay for it.

~J.Laborde

thank you!
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.016 seconds with 17 queries. (Pretty URLs adds 0s, 0q)