|
airtite
|
 |
« on: February 07, 2012, 11:14:07 AM »
|
|
|
Hi
with mpps I am not seeing any voltage, vcds connects fine, nefmoto flasher connects using slow init and a 800 memory layout but doesnt read (log attached)
|
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
 Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #1 on: February 07, 2012, 03:33:29 PM »
|
|
|
This is the problem reported in the log file when trying to start the programming session: ConditionsNotCorrectOrRequestSequenceError.
Is the ECU on the bench or in the car?
I would test again with version 1.9.2.2 or later because it has better support for starting diagnostic sessions. I would specifically try connecting at 10400 baud to see if that solves the problem.
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #2 on: February 08, 2012, 12:41:12 AM »
|
|
|
thanks Tony, ecu still in the car. I am just using the 800 memory layout because that seemed too work fine in the 1.8T b6, should I be using another memory layout?
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #3 on: February 08, 2012, 10:11:42 AM »
|
|
|
nope new version and changing baud didnt help, log to follow.
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #4 on: February 09, 2012, 01:04:35 PM »
|
|
|
log
|
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #5 on: February 09, 2012, 01:09:26 PM »
|
|
|
Thanks for posting the log. Version 1.9.2.2 and using 10400 baud does allow for a successful connection.
The problem appears to be that the ECU is giving negative responses when trying to read the flash memory.
Does this ECU have an aftermarket tune on it?
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #6 on: February 10, 2012, 01:31:58 AM »
|
|
|
Thanks for posting the log. Version 1.9.2.2 and using 10400 baud does allow for a successful connection.
The problem appears to be that the ECU is giving negative responses when trying to read the flash memory.
Does this ECU have an aftermarket tune on it?
Hi Tony Not that I am aware of, the thing is I get the same result on my 1.8T b6 as well and that has my own tuned file on there so I suspect its something else. |
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #7 on: February 10, 2012, 06:23:52 PM »
|
|
|
It is entirely possible that the ECU does not support being read.
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #8 on: February 12, 2012, 12:54:47 AM »
|
|
|
It is entirely possible that the ECU does not support being read.
I would agree with you but the thing is mpps seems too read/write my 1.8T ecu fine, nefmoto will write too the 1.8T but not read. mpps seems too have the s4 model there but doesnt seem too pick up voltage and I dont have a stock file too test if nefmoto would write the s4 file.... to me it seems as if nefmoto flasher in general has an issue with the b6 model ecu's? |
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #9 on: February 13, 2012, 02:49:01 PM »
|
|
|
I don't own any B6 ECUs for testing, so it is possible there are some variations to the B6 the NefMoto software doesn't support.
It is also possible that MPPS is not using the official KWP2000 protocol for flashing, and instead is using some backdoor method. To verify this we would need to use a logic analyzer or serial port monitor to record the protocol MPPS is using.
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #10 on: March 26, 2012, 01:35:39 AM »
|
|
|
sorry to dig this up again.
I have spoken to quite a few tuners and all of them say that this ECU should be port flashable, so I am hoping someone here can help me troubleshoot this issue.
So a quick refresher, my MPPS clone is not picking up external voltage from the ECU when connected, the nefmoto flasher connects but then cant read the file. VCDS etc connects and allows me to clear faults/log/etc. I have checked all fuses and made sure I am plugging the port in correctly is there any connectors between the OBD port and the ECU that may have possibly come loose that would cause this?
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #11 on: March 26, 2012, 11:21:58 PM »
|
|
|
anyone know if I would be able too use one of these too program my ECU? http://www.xeltek.com/pages.php?pageid=255Does the ECU just plug directly into this device or do I still need some sort of connector? |
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #12 on: May 10, 2012, 02:49:32 AM »
|
|
|
OK finally finally managed too get a read with my new galleto 1260 BUT when checking the file with ME7checker I am getting an RSA failure?
==============================================================================
ME7Check_linux v1.11 (c) mki, 06/2004-07/2011
Checking file s4_test.ori (size=1048576)
Reading Version Strings...
-> Bootrom Version = embedded in CPU, asume 06.02/06.05
-> EPK = 42/1/ME7.1.1/5/8542.04//25E/DstH2o/030303//
-> Contents of ECUID data table:
- '0261207994' (SSECUHN)
- '1037366491' (SSECUSN)
- '8E0910560D ' (VAG part number)
- '0010' (VAG sw number)
- '4.2L V8/5V ' (engine id)
-> Contents of ECUID data table:
- 'HW_MAN004'
RSA signature failure found
-> Found 1 error!!! *******************************
|
|
|
|
|
Logged
|
|
|
|
|
RaraK
|
|
« Reply #13 on: May 11, 2012, 05:24:39 AM »
|
|
|
I find issues with all audi platform cars after 2002 here in the states, even with my kwp(orig) sometimes. KWP gets the 1.8t's almost all the time, but sometimes there are cars which i just cannot read or write without boot mode.
cars i saw this on were a 2004 1.8t(bone stock for sure), b6 s4, b7 a4(2.0tfsi)
|
|
|
|
|
Logged
|
|
|
|
|
airtite
|
|
« Reply #14 on: May 12, 2012, 12:47:47 AM »
|
|
|
does this mean its not safe too modify, checksum and reflash with this file?
|
|
|
|
|
Logged
|
|
|
|
|
