Pages: [1]
Author Topic: Lanch control and antilag ME7.5 1.8T s3 Amk 210hp  (Read 4687 times)
drews3
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 6


« on: October 31, 2018, 12:10:53 AM »

Hello people

So i searched a bit of time for the antilag function and after some time i found it and i saw it is usable in me7.5
the point is i have found the function i have implemented it in my file now i writted it with kess and locked the ecu Cry so i took it down and
gooing to writte it on bench now my question is my tool blocked the ecu or i done somthing wrong on the file ...
however here it goes

-The condition is located at adress: 17e00

A6   01   50   46   0A   00   F0   55   E6   FF   FF   FF   FF   FF   FF   FF

-The function is located at adress: 0A6100

9A   2B   13   80   F2   F4   40   8E   D7   00   81   00   F2   F9   00   7E
40   49   9D   0B   F2   F4   7A   F8   D7   00   81   00   F2   F9   02   7E
40   49   FD   03   F7   8E   AC   8D   0D   2F   9A   2B   29   80   8A   2B
22   60   F2   F4   7A   F8   D7   00   81   00   F2   F9   06   7E   40   49
FD   1A   C2   F4   02   8B   D7   00   81   00   C2   F9   08   7E   40   49
FD   12   D7   00   38   00   F2   F4   F0   4F   D7   00   81   00   F2   F9
04   7E   40   49   9D   11   F7   8E   AC   8D   08   41   D7   00   38   00
F7   F8   F0   4F   0D   09   D7   00   38   00   F6   8F   F0   4F   0D   04
D7   00   38   00   F6   8E   F0   4F   F3   F8   F3   8A   DB   00   FF   FF



-Searched at end of the file D7 40 06 02 03 F8   and added my recal for the function it was added before "DA 81 00 6A-here i recalled my function" adress
 adress 9DD50

what i done wrong was fault of my file or fault of my tool kess asked me the oem file for compare so i think is fault of my kess but maybe i missed something in the file :\

in attachment the oem file withstage1 and the modified file i used winols to mdoify the file .
if somone can give me a finger(because i want to understand what i done wrong and what i done right) not a hand  Grin i would be happy to pay him a beer Smiley
Logged
drews3
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 6


« Reply #1 on: November 01, 2018, 01:33:37 AM »

still have long way to go
« Last Edit: November 01, 2018, 05:36:56 AM by drews3 » Logged
Kompiesto
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 109


« Reply #2 on: November 05, 2018, 06:18:13 AM »

You dont undrestand what you are doing....

You cant copy and paste code dedicated for S4 Mbox (7.1) to S3 (7.5) ecu.
Code can work but all needed variables is in different locations. You must find variables in your file and modify pasted code.

Kess working properly. Kess compare ori file to calculate checksum. Now only way to get working your car is write ori flash in bootmode.
Logged
Dejw0089
Full Member
***

Karma: +2/-6
Offline Offline

Posts: 100



« Reply #3 on: November 15, 2018, 11:24:52 AM »

I has amk leon and you cant only change call function. You must change main function too witch correct adress for variables etc
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.014 seconds with 16 queries. (Pretty URLs adds 0s, 0q)