2004 Audi A6 2.7T 6MT

Self-tuned ME7.1.1 4z7907551R

BEL Block
 H-beam rods
 Stock pistons
 034 coated bearings
 ARP main studs
 ARP head studs

2.8l rebuilt heads
 Supertech stainless steel exhaust valves
 Lightly ported (gasket matched intake side)

SRM RS6/K24 Turbos

Dual In-tank Walbro 450s
034 fuel rails (-6AN equally fed)
Fuelab AFPR (set to 4 bar)
Bosch EV14 1100cc injectors

Zeitronix ZT-2 with Multi-Gauge (AFR, MAP, EGT, & fuel pressure)

IE catch can (breather modified to draw vacuum from y-pipe)
Stock Airbox (Front lower triangle cut out)
HPX MAF Sensor (in 73mm stock housing)
Stock Y-pipe
SRM 2" turbo inlets
Silicone boost hoses and couplers
Forge 007P BPVs
RS4 Intake manifold
RS4 Throttle body
034 Phenolic intake manifold spacer
 
Rennsport Fabrication tubular exhaust manifolds
3" Downpipes & mid-pipes
Dual 2.5" exhaust (Vibrant mufflers & resonators)

VAST Snub Mount
Stern Pro Engine Mounts
Stern Pro Transmission Mounts
H&R rear anti-sway bar

Southbend single mass flywheel
Southbend stage 4 extreme clutch

6-speed 01E - Rebuilt by AAM
 JHM Solid stabilizer bushing
 JHM Upgraded linkage cross-rod
 JHM Solid Linkage upgrade
 JHM Solid shifter centering spring
 JHM Short throw shifter
 JHM Weighted shift knob
 USP Metal slave & line kit

Hawk HPS Street brake pads - front & rear

034 Power steering cooler

Battery relocated to trunk

Anthracite Metallic Gray 17" stock wheels
245/45 BFGoodrich G-Force Sport Comp-2 tires

Future Plans:
 2-in / 1-out vertical flow FMIC with blow through MAF
 Coil-overs
 C5 RS6 9-Spoke Wheels (18x8.5)

Well one of my k03's is toast so it looks like it's time to go to stage 3 (3- for now).

I've decided to go with GT2560R (GT28R) Turbos. Not an eliminator kit, just the turbos themselves. It's gonna end up being a lot of money and work for minimal gains right now, but thats okay - I like having the room to keep expanding. I'm welding a T25 flange onto the stock exhaust manifolds, and porting them out a little bit for a smooth transition to the turbine inlet. I'll modify my current downpipes to connect to a v-band discharge on the turbos, and put together a cat-back exhaust. It's also time to finish up the FMIC and put together compressor inlets/outlets. Until I can afford a real fueling set-up I'm going to have to run stock injectors with a 5 bar FPR.

Everything's been ordered so I'll be able to get started this weekend.

I'm really looking forward to putting everything together, and especially really getting into tuning for the new setup! I should have my zeitronix set-up by the time I'm finished with everything else so I'll be able to properly tune the fueling.

Yeah barely. As long as you weld the T25 flange in at the right angle (requiring custom compressor inlets/outlets), but that's a huge pita due to the cast double-wall design of the stock manifolds... Which is why I've decided to ditch the stock manifolds and put together some new ones, likely still log-style for simplicity and cost. Especially considering I won't be trying to squeeze every last bit of hp out of the car on the stock block and tip trans.