dilly
|
|
« on: June 25, 2019, 09:57:47 PM »
|
|
|
got an s4 6mt and i read the flash all fine and dandy but as soon as i want to flash it of course it doesnt work any ideas? here is nefmoto's output log it always fails the data transfer exit after the first block nefmoto has worked flawlessly for me in the past. i am not sure if this ecu is too stubborn or what if i am missing something lmk so i can get it Validated FTDI device is in dumb mode. Disconnected Connecting... Starting fast init connection. Connecting to address 0x01. Fast init sent, sending start communication request. Switching to KWP2000 session. Connected Disabling Windows sleep mode. Writing ECU flash memory. ECU reports programming session preconditions have been met. Negotiating communication timings. Successfully changed to new communication timings. Requesting security access. ECU reports that security access is not supported. Starting diagnostic session. Successfully started diagnostic session. Negotiating communication timings. Successfully changed to new communication timings. Requesting security access. Security access granted. Validating flash memory starts at 0x00800000 and ends at 0x00900000. Memory layout is valid. Starting to flash data block. Calculating flash checksum to determine if flashing is necessary for range: 0x00800000 to 0x00804000 Flash checksum does not match new data, flashing is necessary. Requesting flash memory erase for address range 0x00800000 to 0x00803FFF. Successfully erased flash memory. Requesting download to ECU for address range 0x00800000 to 0x00803FFF. Request download to ECU succeeded. Starting data transfer. Data transfer failed. Requesting data transfer exit. Failed to exit data transfer. Failed to properly exit flash transfer. Transfering invalid data to force flashing to fail. Starting data transfer. Data transfer failed. Requesting data transfer exit. Failed to exit data transfer. Writing ECU flash memory failed. 100% complete. Restoring Windows sleep mode. Requesting data transfer exit. Failed to exit data transfer. Disconnecting... Disconnected
|
|
|
Logged
|
|
|
|
prj
|
|
« Reply #1 on: June 26, 2019, 12:44:47 AM »
|
|
|
Wrong chip in ECU or encryption board.
|
|
|
Logged
|
|
|
|
_nameless
|
|
« Reply #2 on: June 26, 2019, 05:31:05 AM »
|
|
|
I got a hand full of these worthless things anyone want one or 50 lol
|
|
|
Logged
|
If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
|
|
|
dilly
|
|
« Reply #3 on: June 26, 2019, 10:24:39 AM »
|
|
|
so simple solution.. just buy a new h or m box?
|
|
|
Logged
|
|
|
|
Blazius
|
|
« Reply #4 on: June 26, 2019, 11:10:01 AM »
|
|
|
The one that has more support available.
|
|
|
Logged
|
|
|
|
_nameless
|
|
« Reply #5 on: June 26, 2019, 11:27:37 AM »
|
|
|
Any apb ecu will work fine
|
|
|
Logged
|
If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
|
|
|
dilly
|
|
« Reply #6 on: June 26, 2019, 01:02:30 PM »
|
|
|
The one that has more support available.
whatever one i can find of those 2 boxes i will be getting i know they are hitachi and cross flashable with recode on cluster thanks for the help guys
|
|
|
Logged
|
|
|
|
prj
|
|
« Reply #7 on: June 27, 2019, 02:02:20 AM »
|
|
|
The one that has more support available.
LOL what did I tell you about keeping it shut when you don't know WTF you are on about? All ME7.1 2.7TT 29F800BB are crossflashable. Can be any S4/RS4/A6 ECU apart from newer ME7.1.1 A6 versions. There are about 20 part numbers that will fit. Doesn't matter Bosch or Hitachi, you can cross flash them all the same.
|
|
|
Logged
|
|
|
|
IamwhoIam
|
|
« Reply #8 on: June 27, 2019, 02:41:10 AM »
|
|
|
What he said
|
|
|
Logged
|
I have no logs because I have a boost gauge (makes things easier)
|
|
|
Blazius
|
|
« Reply #9 on: June 27, 2019, 11:42:43 AM »
|
|
|
LOL what did I tell you about keeping it shut when you don't know WTF you are on about?
All ME7.1 2.7TT 29F800BB are crossflashable. Can be any S4/RS4/A6 ECU apart from newer ME7.1.1 A6 versions. There are about 20 part numbers that will fit.
Doesn't matter Bosch or Hitachi, you can cross flash them all the same.
The hell you are on about ? I said use a flash or anything that has the most support aka damos etc available. I dont care if its crossflashed, bought stock or whatever, I just said use the logical ecu/bin/flash whatever. jesus christ , if you have a wish to pick fights with members do it with somebody else please , What I said has little to do with what you said, or you need to severely rethink your attitude it seems. ffs Unbelievable for such a "respected" tuner on this forum. Lmao.
|
|
« Last Edit: June 27, 2019, 11:51:48 AM by Blazius »
|
Logged
|
|
|
|
dilly
|
|
« Reply #10 on: June 27, 2019, 12:38:23 PM »
|
|
|
LOUD NOISES guys relax this has all been helpful and reasonable info. Personally i did not know all the me7.1 2.7 ecu's can be crossflashed. i found a spare A box in my trunk that had a normal 800bb chip on the board and i flashed a m box file and recoded cluster to iirc 1027 and now i have a tach and no powertrain errors. no need to try and rip each other a new one bois thank you all for the support. i will most likely be needing more as i will make a new topic about deleting a pcode unless i find one already posted btw here is what the inside of my h box looked like i assume this is from a company or is it stock?? https://gyazo.com/f9c1850bc0d05bc03fa2deacb7eba4a2
|
|
|
Logged
|
|
|
|
dilly
|
|
« Reply #11 on: June 27, 2019, 12:39:07 PM »
|
|
|
LOUD NOISES guys relax this has all been helpful and reasonable info. Personally i did not know all the me7.1 2.7 ecu's can be crossflashed. i found a spare A box in my trunk that had a normal 800bb chip on the board and i flashed a m box file and recoded cluster to iirc 1027 and now i have a tach and no powertrain errors. no need to try and rip each other a new one bois thank you all for the support. i will most likely be needing more as i will make a new topic about deleting a pcode unless i find one already posted btw here is what the inside of my h box looked like i assume this is from a company or is it stock?? https://gyazo.com/f9c1850bc0d05bc03fa2deacb7eba4a2
|
|
|
Logged
|
|
|
|
IamwhoIam
|
|
« Reply #12 on: June 27, 2019, 01:35:44 PM »
|
|
|
|
|
|
Logged
|
I have no logs because I have a boost gauge (makes things easier)
|
|
|
dilly
|
|
« Reply #13 on: June 27, 2019, 01:40:19 PM »
|
|
|
APR EMCS
interesting. car ran like shit with that ecu lol. i am ssuming it is some what of a stage one tune from apr. worth anything? flashed the community stage 1 until i get everything sorted with inspection and car runs good
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #14 on: June 27, 2019, 10:16:29 PM »
|
|
|
interesting. car ran like shit with that ecu lol. i am ssuming it is some what of a stage one tune from apr. worth anything?
flashed the community stage 1 until i get everything sorted with inspection and car runs good
No. You can't flash over it unless you desolder and put in a normal flash. You should have started with looking at the ECU first before doing anything.
|
|
|
Logged
|
|
|
|
|