golfracer0
Newbie
Karma: +0/-0
 Offline
Posts: 7
|
 |
« on: October 19, 2019, 04:35:02 PM »
|
|
|
so i have been all over this forum and i have noted a pretty hefty hole when it comes to info on these cars and the family of ecus. i have tried pretty much every thing i have come across other then removing the chip and getting an eeprom reader/flasher to get a bin file or to flash. at this point though im just trying to get nef to actually connect to my car. i have successfully connected to my mk4 jetta wago 2.0 and have pulled a bin from that car, also vcds will connect to my mk3 and if had the reg version i would be able to log there so i assume that i should in theory be able to log and connect with nef.... annnnnny way here is the log that nef is spitting out. if anyone can shed some light onto why this is happening i will be super great full for the help.
Switching to KWP2000 session.
10/Oct/2019 02:46:42.910: LOG: Opened FTDI device.
10/Oct/2019 02:46:42.911: LOG: FTDI device info - Description: FT232R USB UART Serial Number: AL00KYCR Device Type: FT_DEVICE_232R ID: 0x4036001 Device Flags: 0x1
10/Oct/2019 02:46:42.959: USER: Validated FTDI device is in dumb mode.
10/Oct/2019 02:46:42.993: LOG: Starting send receive thread.
10/Oct/2019 02:46:42.994: LOG: Send receive thread now started.
10/Oct/2019 02:46:42.995: USER: Disconnected
10/Oct/2019 02:46:43.015: LOG: Setting communication timings to defaults.
10/Oct/2019 02:46:43.016: USER: Connecting...
10/Oct/2019 02:46:43.035: LOG: Setting communication timings to defaults.
10/Oct/2019 02:46:43.036: USER: Starting slow init connection.
10/Oct/2019 02:46:45.636: USER: Connecting to address 0x01.
10/Oct/2019 02:46:47.851: LOG: Read incorrect sync byte, guessing baud rate is actually 9600.
10/Oct/2019 02:46:47.911: USER: Slow init succeeded.
10/Oct/2019 02:46:47.911: LOG: Setting Address: 0x01 KeyByte1: 0x01 KeyByte2: 0x0A
10/Oct/2019 02:46:47.912: USER: Switching to KWP1281 session.
10/Oct/2019 02:46:48.078: LOG: KWP1281 read block
10/Oct/2019 02:46:48.142: LOG: KWP1281 sent block
10/Oct/2019 02:46:48.298: LOG: KWP1281 read block
10/Oct/2019 02:46:48.361: LOG: KWP1281 sent block
10/Oct/2019 02:46:48.507: LOG: KWP1281 read block
10/Oct/2019 02:46:48.571: LOG: KWP1281 sent block
10/Oct/2019 02:46:48.657: LOG: KWP1281 read block
10/Oct/2019 02:46:48.723: LOG: KWP1281 sent block
10/Oct/2019 02:46:48.759: LOG: KWP1281 read block
10/Oct/2019 02:46:48.822: LOG: KWP1281 sent block
10/Oct/2019 02:46:48.823: USER: KWP1281 connect info: 037906259D MOTRONIC M5.9 HS V04 B
10/Oct/2019 02:46:50.324: USER: Connecting to address 0x01.
10/Oct/2019 02:46:53.138: LOG: Failed to read sync byte, guessing baud rate is actually 9600.
10/Oct/2019 02:46:53.178: LOG: Not enough key bytes, read: 0
10/Oct/2019 02:46:53.195: USER: Slow init failed.
10/Oct/2019 02:46:53.196: USER: Disconnected
10/Oct/2019 02:46:53.239: LOG: Setting communication timings to defaults.
10/Oct/2019 02:46:53.240: USER: Connecting...
10/Oct/2019 02:46:53.259: LOG: Setting communication timings to defaults.
10/Oct/2019 02:46:53.260: USER: Starting slow init connection.
10/Oct/2019 02:46:55.861: USER: Connecting to address 0x01.
10/Oct/2019 02:46:58.071: LOG: Read incorrect sync byte, guessing baud rate is actually 9600.
10/Oct/2019 02:46:58.132: USER: Slow init succeeded.
10/Oct/2019 02:46:58.300: LOG: KWP1281 read block
10/Oct/2019 02:46:58.364: LOG: KWP1281 sent block
10/Oct/2019 02:46:58.520: LOG: KWP1281 read block
10/Oct/2019 02:46:58.583: LOG: KWP1281 sent block
10/Oct/2019 02:46:58.729: LOG: KWP1281 read block
10/Oct/2019 02:46:58.793: LOG: KWP1281 sent block
10/Oct/2019 02:46:58.879: LOG: KWP1281 read block
10/Oct/2019 02:46:58.943: LOG: KWP1281 sent block
10/Oct/2019 02:46:58.979: LOG: KWP1281 read block
10/Oct/2019 02:46:59.043: LOG: KWP1281 sent block
10/Oct/2019 02:46:59.043: USER: KWP1281 connect info: 037906259D MOTRONIC M5.9 HS V04 B
10/Oct/2019 02:47:00.544: USER: Connecting to address 0x01.
10/Oct/2019 02:47:03.360: LOG: Failed to read sync byte, guessing baud rate is actually 9600.
10/Oct/2019 02:47:03.399: LOG: Not enough key bytes, read: 0
10/Oct/2019 02:47:03.416: USER: Slow init failed.
10/Oct/2019 02:47:03.417: USER: Disconnected
10/Oct/2019 02:47:03.456: LOG: Setting communication timings to defaults.
10/Oct/2019 02:47:03.457: USER: Connecting...
10/Oct/2019 02:47:03.481: LOG: Setting communication timings to defaults.
10/Oct/2019 02:47:03.481: USER: Starting slow init connection.
10/Oct/2019 02:47:06.082: USER: Connecting to address 0x01.
10/Oct/2019 02:47:08.290: LOG: Read incorrect sync byte, guessing baud rate is actually 9600.
10/Oct/2019 02:47:08.353: USER: Slow init succeeded.
10/Oct/2019 02:47:08.520: LOG: KWP1281 read block
10/Oct/2019 02:47:08.584: LOG: KWP1281 sent block
10/Oct/2019 02:47:08.740: LOG: KWP1281 read block
10/Oct/2019 02:47:08.803: LOG: KWP1281 sent block
10/Oct/2019 02:47:08.951: LOG: KWP1281 read block
10/Oct/2019 02:47:09.013: LOG: KWP1281 sent block
10/Oct/2019 02:47:09.101: LOG: KWP1281 read block
10/Oct/2019 02:47:09.165: LOG: KWP1281 sent block
10/Oct/2019 02:47:09.201: LOG: KWP1281 read block
10/Oct/2019 02:47:09.265: LOG: KWP1281 sent block
10/Oct/2019 02:47:09.265: USER: KWP1281 connect info: 037906259D MOTRONIC M5.9 HS V04 B
10/Oct/2019 02:47:10.767: USER: Connecting to address 0x01.
10/Oct/2019 02:47:12.983: LOG: Read incorrect sync byte, guessing baud rate is actually 9600.
10/Oct/2019 02:47:13.045: USER: Slow init succeeded.
10/Oct/2019 02:47:13.212: LOG: KWP1281 read block
10/Oct/2019 02:47:13.276: LOG: KWP1281 sent block
10/Oct/2019 02:47:13.432: LOG: KWP1281 read block
10/Oct/2019 02:47:13.496: LOG: KWP1281 sent block
10/Oct/2019 02:47:13.641: LOG: KWP1281 read block
10/Oct/2019 02:47:13.705: LOG: KWP1281 sent block
10/Oct/2019 02:47:13.791: LOG: KWP1281 read block
10/Oct/2019 02:47:13.855: LOG: KWP1281 sent block
10/Oct/2019 02:47:13.891: LOG: KWP1281 read block
10/Oct/2019 02:47:13.955: LOG: KWP1281 sent block
10/Oct/2019 02:47:13.955: USER: KWP1281 connect info: 037906259D MOTRONIC M5.9 HS V04 B
10/Oct/2019 02:47:15.456: USER: Connecting to address 0x11.
10/Oct/2019 02:47:18.271: LOG: Failed to read sync byte, guessing baud rate is actually 9600.
10/Oct/2019 02:47:18.310: LOG: Not enough key bytes, read: 0
10/Oct/2019 02:47:18.326: USER: Slow init failed.
10/Oct/2019 02:47:18.327: USER: Disconnected
|
|
|
|
|
Logged
|
|
|
|
|
Blazius
|
|
« Reply #1 on: October 19, 2019, 04:41:40 PM »
|
|
|
Try slow 0x00
|
|
|
|
|
Logged
|
|
|
|
golfracer0
Newbie
Karma: +0/-0
Offline
Posts: 7
|
|
« Reply #2 on: October 19, 2019, 04:47:17 PM »
|
|
|
in settings is that connection address? its set to 0x01 atm
|
|
|
|
|
Logged
|
|
|
|
golfracer0
Newbie
Karma: +0/-0
Offline
Posts: 7
|
|
« Reply #3 on: October 19, 2019, 06:07:54 PM »
|
|
|
Try slow 0x00
where can i change this setting? |
|
|
|
|
Logged
|
|
|
|
|
_nameless
|
|
« Reply #4 on: October 19, 2019, 07:25:50 PM »
|
|
|
Nefmoto wont read m5.92 chip burner read or minimon (or somthing like that) use mpps to write
|
|
|
|
|
Logged
|
Giving your mom a tuneup
|
|
|
|
Blazius
|
|
« Reply #5 on: October 19, 2019, 09:10:19 PM »
|
|
|
Yes its conn adress, but as pointed out, are you trying to use nefmoto with m5 ?
|
|
|
|
|
Logged
|
|
|
|
|
dilly
|
|
« Reply #6 on: October 19, 2019, 10:25:12 PM »
|
|
|
Nefmoto wont read m5.92 chip burner read or minimon (or somthing like that) use mpps to write
Yes its conn adress, but as pointed out, are you trying to use nefmoto with m5 ?
i was gonna point this out but figured i keep quiet... |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #7 on: October 20, 2019, 11:33:43 AM »
|
|
|
Nefmoto flasher does not support that ECU.
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
golfracer0
Newbie
Karma: +0/-0
Offline
Posts: 7
|
|
« Reply #8 on: October 24, 2019, 12:03:23 AM »
|
|
|
thanks for the info guys been banging my head agaimst a wall for a while ofer this one lol!!! ordered an eprom flasher gonna try that route will make a post on my progress!!
|
|
|
|
|
Logged
|
|
|
|
|
Blazius
|
|
« Reply #9 on: October 24, 2019, 04:09:06 AM »
|
|
|
thanks for the info guys been banging my head agaimst a wall for a while ofer this one lol!!! ordered an eprom flasher gonna try that route will make a post on my progress!!
MPPS does R&W thru obd on me 5.9. |
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #10 on: October 24, 2019, 04:52:50 AM »
|
|
|
every single person or post in this thread is wrong or has no idea what they are talking about (except nyet).
|
|
|
|
|
Logged
|
|
|
|
|
Blazius
|
|
« Reply #11 on: October 24, 2019, 10:22:22 AM »
|
|
|
every single person or post in this thread is wrong or has no idea what they are talking about (except nyet).
I am sorry , but MPPS does M3 write but not read, but it does do both on M5.9 doesn't it, also most american and canadian dbc cars are m5.9. If its wrong , please bless this thread with another intellectual post.  |
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #12 on: October 24, 2019, 12:44:45 PM »
|
|
|
I am sorry , but MPPS does M3 write but not read, but it does do both on M5.9 doesn't it, also most american and canadian dbc cars are m5.9. If its wrong , please bless this thread with another intellectual post. again, zero clue what you are babbling on about. just adding more incoherent nonsense to a thread that is already full to the brim with such. |
|
|
|
|
Logged
|
|
|
|
golfracer0
Newbie
Karma: +0/-0
Offline
Posts: 7
|
|
« Reply #13 on: October 25, 2019, 02:21:47 AM »
|
|
|
any chance we could get a nugget of gold?? so far what i have gleaned from the info here is that nef wont do what im trying to do and that i need to start looking at mpps and or flashing the chip directly.....close?  |
|
|
|
|
Logged
|
|
|
|
|
dilly
|
|
« Reply #14 on: October 25, 2019, 10:20:59 PM »
|
|
|
any chance we could get a nugget of gold?? so far what i have gleaned from the info here is that nef wont do what im trying to do and that i need to start looking at mpps and or flashing the chip directly.....close? nefmoto is a me7 utility that should be your answer |
|
|
|
|
Logged
|
|
|
|
|
